3dprinters
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
3dprinters [2014-06-10 05:29] – jane | 3dprinters [2023-10-31 22:04] – river | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== 3D Printers ====== | ====== 3D Printers ====== | ||
- | === Maker Bot === | + | === Costs === |
- | Currently not working. Extruder isn't working and the firmware on it is the wrong one. Needs loads of work. | + | ^Material^Members/ |
+ | |1.75mm PLA|£0.30/ | ||
+ | |3.00/2.85mm PLA|£0.50/ | ||
- | === Prusa Style === | + | === Original |
+ | Ownership: Miron Zadora\\ | ||
+ | Status: Working\\ | ||
+ | Location: G14\\ | ||
+ | Filament: 1.75 mm | ||
- | Work in progress. Needs firmware reloaded and motor connectors put onto the cables. | + | === Original Prusa Mini === |
+ | [[prusa_mini|Prusa Mini]]\\ | ||
+ | Ownership: TBD\\ | ||
+ | Location: G14\\ | ||
+ | Filament: TBD | ||
- | === 3D RepRap | + | === Ultimaker 2 === |
- | [[http:// | + | [[ultimaker2|Ultimaker 2]]\\ |
- | RAMPS 1.2 board, the electronics board that controls the printing process. | + | Ownership: Hacklab. Bought December 2014.\\ |
+ | Filament: 3.00/2.85mm\\ | ||
- | Location:in the store, | + | === Voron 2.4r2 === |
+ | [[voron_2_4_r2|Voron 2.4 r2]]\\ | ||
+ | Ownership: Jacob Lewis\\ | ||
+ | Status: Being tuned, but works, message Jacob on Discord for help using\\ | ||
+ | Location: G14\\ | ||
+ | Filament: 1.75 mm\\ | ||
+ | |||
+ | ====== Approved filaments ====== | ||
+ | |||
+ | Be careful as our printers use different diameter filament! | ||
+ | |||
+ | Most of these can be bought on amazon.\\ | ||
+ | You can also try asking on the mailing list as some members may be willing to sell some of their own. | ||
+ | |||
+ | ==== PLA ==== | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | |||
+ | ==== PETG ==== | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | |||
+ | ====== Old 3D printers ===== | ||
+ | |||
+ | === 3D RepRap === | ||
+ | [[http:// | ||
+ | Ownership: Matt Ellis\\ | ||
+ | RAMPS 1.2 board, the electronics board that controls the printing process.\\ | ||
+ | Location:in the store, | ||
Status: semi-working, | Status: semi-working, | ||
- | === Ultimaker 2 === | + | === Maker Bot === |
+ | Ownership: < | ||
+ | Status: Currently not working, (worked before)\\ | ||
+ | Extruder isn't working and the firmware on it is the wrong one. Needs loads of work. | ||
+ | |||
+ | === Prusa Style === | ||
+ | Ownership: unclear\\ | ||
+ | Work in progress. Needs firmware reloaded and motor connectors put onto the cables. | ||
3dprinters.txt · Last modified: 2024-02-06 19:25 by jaso55555