3dprinters
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
3dprinters [2018-09-06 19:46] – DavidW | 3dprinters [2020-10-08 14:38] – changed prusa mk3 to mk3s MirZa | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== 3D Printers ====== | ====== 3D Printers ====== | ||
- | === 3D RepRap | + | === Original Prusa i3 MK3s === |
- | [[http:// | + | [[prusa_i3_mk_3|Prusa i3 MK3s]]\\ |
- | Ownership: | + | Ownership: |
- | RAMPS 1.2 board, the electronics board that controls the printing process.\\ | + | Status: |
- | Location:in the store, | + | Location: G11\\ |
- | Status: | + | Filament: 1.75 mm |
- | + | ||
- | === Maker Bot === | + | |
- | Ownership: < | + | |
- | Status: Currently not working, (worked before)\\ | + | |
- | Extruder isn't working and the firmware on it is the wrong one. Needs loads of work. | + | |
- | + | ||
- | === Original Prusa i3 MK 2 === | + | |
- | Ownership: David Weis\\ | + | |
- | Status: Work in progress.\\ | + | |
- | See [[Prusa i3 MK 2]] | + | |
- | + | ||
- | === Prusa Style === | + | |
- | Ownership: unclear\\ | + | |
- | Work in progress. Needs firmware reloaded and motor connectors put onto the cables. | + | |
=== Ultimaker 2 === | === Ultimaker 2 === | ||
- | Ownership: Hacklab. Bought December 2014. See [[ultimaker2|Ultimaker | + | [[ultimaker2|Ultimaker 2]]\\ |
+ | Ownership: Hacklab. Bought December 2014.\\ | ||
+ | Filament: 3.00/2.85mm\\ | ||
====== Approved filaments ====== | ====== Approved filaments ====== | ||
- | Most of these can be bought on amazon. | + | Be careful as our printers use different diameter filament! |
+ | |||
+ | Most of these can be bought on amazon.\\ | ||
You can also try asking on the mailing list as some members may be willing to sell some of their own. | You can also try asking on the mailing list as some members may be willing to sell some of their own. | ||
Line 33: | Line 24: | ||
* [[https:// | * [[https:// | ||
* [[https:// | * [[https:// | ||
- | * RS Pro | + | * [[https:// |
* [[https:// | * [[https:// | ||
* [[https:// | * [[https:// | ||
Line 40: | Line 31: | ||
* [[https:// | * [[https:// | ||
* [[https:// | * [[https:// | ||
+ | |||
+ | ====== Old 3D printers ===== | ||
+ | |||
+ | === 3D RepRap === | ||
+ | [[http:// | ||
+ | Ownership: Matt Ellis\\ | ||
+ | RAMPS 1.2 board, the electronics board that controls the printing process.\\ | ||
+ | Location:in the store, \\ | ||
+ | Status: semi-working, | ||
+ | |||
+ | === Maker Bot === | ||
+ | Ownership: < | ||
+ | Status: Currently not working, (worked before)\\ | ||
+ | Extruder isn't working and the firmware on it is the wrong one. Needs loads of work. | ||
+ | |||
+ | === Prusa Style === | ||
+ | Ownership: unclear\\ | ||
+ | Work in progress. Needs firmware reloaded and motor connectors put onto the cables. | ||
+ |
3dprinters.txt · Last modified: 2024-02-06 19:25 by jaso55555