doorcontroller2
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
doorcontroller2 [2016-06-26 00:30] – [Controller] tim | doorcontroller2 [2017-02-04 11:17] – tim | ||
---|---|---|---|
Line 13: | Line 13: | ||
* http:// | * http:// | ||
+ | ^ Reference ^ Component ^ Farnell ^ | ||
+ | | C1 | 1206 10uF 25V | 2320887 | | ||
+ | | C2 | 1206 22uF 6.3V | 2320911 | | ||
+ | | C3, C4 | 0603 0.1uF 6.3V | 1759016 | | ||
+ | | D1 | SMA diode B230A | 1843686 | | ||
+ | | D2 | SMA diode (flyback protection) | 1625280 | | ||
+ | | JP1 | PCB male header 2.54mm pitch 3-way | | | ||
+ | | JP2 | PCB male header 2.54mm pitch 2-way | | | ||
+ | | L1 | Coilcraft LPS6225-472MRB 4.7uH 2A | 2408256 | | ||
+ | | P1, P2, P3 | PCB screw terminals 5.08mm pitch 2-way (9 total) | | | ||
+ | | P4 | PCB male header 2.54mm pitch 6-way | | | ||
+ | | Q1, Q2 | MOSFET-N SOT-23 | 2069541 | | ||
+ | | R1 | 0603 31K6 1% | 2059454 | | ||
+ | | R3 | 0603 56K 1% | 2303215 | | ||
+ | | R2, R4 | 0603 10K2 1% | 2059407 | | ||
+ | | R5, R6, R7, R9, R10, R11 | 0603 10K 1% | 2303192 | | ||
+ | | R8 | 0603 2K2 1% | 2303166 | | ||
+ | | SW1 | EVQPT5 tactile switch | 2425617 | | ||
+ | | U1 | ADP2301 | | | ||
+ | | U2 | SRD 12V relay | | | ||
+ | | U3 | ESP-12E | | | ||
+ | | between GND/12V_OUT | generic through-hole flyback diode | | ||
+ | |||
+ | [todo: assembly notes, add diode to switched 12V output, configure relay mode with jumper] | ||
===== Reader ===== | ===== Reader ===== | ||
CAD files: {{: | CAD files: {{: | ||
+ | |||
+ | Circuit diagram: {{: | ||
{{: | {{: | ||
Line 76: | Line 102: | ||
The mounting plate should secure itself reasonably well with a push-fit, but consider adding a rubber foot or a blob of hot-melt glue to prevent it from rocking. | The mounting plate should secure itself reasonably well with a push-fit, but consider adding a rubber foot or a blob of hot-melt glue to prevent it from rocking. | ||
- | Drill two holes in the enclosure lid for the LED and push-button. | + | Drill a large hole in the side of the enclosure for wiring. Drill screw holes for wall-mounting. |
The push-button and LED may be wired as two separate pairs, or with a shared GND. The LED should have a 120R series resistor. | The push-button and LED may be wired as two separate pairs, or with a shared GND. The LED should have a 120R series resistor. | ||
Line 83: | Line 109: | ||
Take care to keep wiring away from the antenna. | Take care to keep wiring away from the antenna. | ||
+ | |||
+ | ===== Firmware ===== | ||
+ | |||
+ | [todo] | ||
+ | |||
+ | ===== Management Server ===== | ||
+ | |||
+ | [todo] | ||
doorcontroller2.txt · Last modified: 2019-02-24 00:40 by tim