g14_setup
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
g14_setup [2019-07-30 16:38] – [Tasks] mike | g14_setup [2019-08-09 18:57] – [Tasks] tim | ||
---|---|---|---|
Line 5: | Line 5: | ||
These tasks can be started now: | These tasks can be started now: | ||
+ | * Shelves (see below) | ||
* Order/ | * Order/ | ||
* Run 4 cat5 cables from G11 rack to G14 roof space | * Run 4 cat5 cables from G11 rack to G14 roof space | ||
- | * Install UniFi access point | + | * Sort/ |
- | * < | + | * Clean ESD mats and trim to match worktops |
- | * Fit benches | + | * <del>Install louvre panels on short wall below conduit [1 done, 2 to go]</ |
- | * < | + | * Steal the worktop that currently covers the 2nd sink in G1. Cut it to make a 150x55cm shelf. |
- | * Attach wooden battens | + | |
- | * <del>Chamfer the worktop edges</ | + | |
- | * Sand & oil the worktops | + | |
- | * < | + | |
- | * < | + | |
- | * < | + | |
- | * Attach legs and fit the worktops, attaching them to the battens with L brackets - slotted so they can move up and down a bit(?) | + | |
+ | ===== Shelves ===== | ||
- | ===== Access control ===== | + | The vertical brackets are installed but we will need to order more horizontals, |
- | < | + | On the narrow end of the room, above the component drawers: |
- | Done! | + | * 3 of 226cm x 30-31cm (slightly less than 226 to allow for the conduit). |
- | ===== Floor ===== | + | To the left of the window: |
- | The floor has damage that will need to be filled. Then it can be painted or covered with vinyl (this is a more practical task than for G1 as the space is small and already empty). | + | * 150cm x 54cm (for the function generator |
+ | * 150cm x 25-30cm (for oscilloscope, | ||
- | ESD flooring has been proposed but is likely to be expensive. We have a roll of ESD flooring but it is soft (anti-fatigue, | + | On the long wall: |
- | The sink cabinet can support its own (empty) weight if the legs are raised. | + | * Many of ~290cm x 30cm (general storage) |
+ | * ~290cm x 25-30cm (for oscilloscope, | ||
- | ===== Networking ===== | + | To the right of the sink, attached to wall and sink unit: |
- | Cables will be run from the server rack in G11 (2-4 would be appropriate). A UniFi access point will be installed (this is in stock). | + | |
- | + | ||
- | ===== Benches and storage ===== | + | |
- | + | ||
- | Proposed: 60-80cm benches against the long walls of the room. No bench on the short ends (because corners are too restrictive). Worktops will be installed at ~75cm height for seated use. | + | |
- | + | ||
- | Use the short end (away from the door) for component drawers and pick bins. Shelving over the benches (some mix of general storage and ready-to-use equipment). | + | |
- | + | ||
- | ==== Cheap IKEA ==== | + | |
- | + | ||
- | [[https:// | + | |
- | + | ||
- | Cheap, but not very durable. | + | |
- | + | ||
- | ==== Solid Wood ==== | + | |
- | + | ||
- | [[https:// | + | |
- | + | ||
- | ==== Storage ==== | + | |
- | + | ||
- | On the short (far) wall: | + | |
- | + | ||
- | | + | |
- | * component drawers above the conduit (up to 7 units can fit across the width of the wall). | + | |
- | * normal shelves above the component drawers | + | |
- | + | ||
- | Above the conduit over the workbenches we will fit twinslot | + | |
- | + | ||
- | * 15-30cm shelves above the conduit | + | |
- | * louvre panels above for other tools and easy-access pick bins. | + | |
- | * normal shelves above the panels. | + | |
- | + | ||
- | [[http:// | + | |
- | [[http:// | + | |
- | Two Raaco panels with bins - £72-£83. | + | |