lasercutter2
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
lasercutter2 [2018-07-21 22:06] – [Safety] alfie | lasercutter2 [2019-07-23 22:46] – [Recommended Settings] mirza | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Laser Cutter #2 ====== | ====== Laser Cutter #2 ====== | ||
- | NOT YET IN SERVICE. | + | TRAINING REQUIRED BEFORE USE.\\ |
- | (Note: | + | (Note: |
Model JD90125\\ | Model JD90125\\ | ||
Line 19: | Line 19: | ||
{{: | {{: | ||
+ | |||
+ | ===== Recommended Settings ===== | ||
+ | Please add your own preferred settings here, but do not edit the existing entries. If you believe a setting is inappropriate, | ||
+ | |||
+ | The test were done in the centre of the cutting bed. | ||
+ | |||
+ | ^ Material ^ Cut Speed ^ Cut Power ^ Notes ^ | ||
+ | | Acrylic 1mm | 30 | 40 | Miron | | ||
+ | | Acrylic 2mm | 28 | 100 | Miron | | ||
+ | | Acrylic 3mm | 17 | 100 | David | | ||
+ | | Acrylic 4mm | 15 | 100 | Miron | | ||
+ | | Acrylic 5mm | 12 | 100 | Miron | | ||
+ | | Acrylic 8mm | 4 | 100 | David | | ||
+ | | Acrylic 10mm | 3 | 100 | Miron | | ||
+ | | Ply 3mm | 20 | 100 | Simon | | ||
+ | | Ply 4mm | 20 | 100 | Miron | | ||
+ | | Ply 6mm | 9 | 100 | Miron | | ||
+ | | MDF 2mm | 30 | 100 | Miron | | ||
+ | | MDF 3mm | 22 | 100 | Miron | | ||
+ | | MDF 4mm | 16 | 100 | Miron | | ||
+ | | MDF 6mm | 10 | 100 | Miron | | ||
+ | | Paper | | | | | ||
+ | | Card | | | | | ||
+ | | Engraving Laminate 1.5mm | 50 | 100 | Miron | | ||
+ | | Engraving Laminate 3mm | | | | | ||
+ | |||
+ | ^ Material ^ Engrave Speed ^ Engrave Power ^ Notes ^ | ||
+ | | Acrylic | 350 | 50 | Miron | | ||
+ | | Ply | 350 | 50 | Miron | | ||
+ | | MDF | 350 | 50 | Miron | | ||
+ | | Laminate | 350 | 50 | Miron | | ||
+ | |||
+ | Minimum power setting for the laser to turn on: 19 | ||
===== To Do ===== | ===== To Do ===== | ||
Line 28: | Line 61: | ||
* < | * < | ||
* < | * < | ||
- | * Create chart of power/speed settings for common materials (as a basic rule, multiply speeds from the old chart by 3x) | + | * <del>Create chart of power/speed settings for common materials (as a basic rule, multiply speeds from the old chart by 3x)</ |
- | * Ply ✔ | + | |
- | * MDF ✘ | + | |
- | * Acrylic ✘ | + | |
* < | * < | ||
* Update docs: | * Update docs: | ||
Line 45: | Line 75: | ||
* < | * < | ||
</ | </ | ||
- | * Create spare focus jigs (requires 12mm acrylic, or a new design) | + | * <del>Create spare focus jigs (requires 12mm acrylic, or a new design)</ |
* Build and install monitoring system (laser usage, temperature logging) | * Build and install monitoring system (laser usage, temperature logging) | ||
* < | * < | ||
Line 58: | Line 88: | ||
* < | * < | ||
</ | </ | ||
- | * Install ducts to roof and upgrade blower, to avoid releasing fumes onto courtyard users. **ACTION: | + | * <del>Install ducts to roof and upgrade blower, to avoid releasing fumes onto courtyard users.</ |
* < | * < | ||
* Replace broken acrylic cover on front-loading slot. | * Replace broken acrylic cover on front-loading slot. | ||
Line 78: | Line 108: | ||
* The air assist is adjustable. Always make sure that it's enabled (on the top control panel) and that the valve (on the right hand side) is open. It's okay to reduce the air assist for delicate materials like paper, but there should always be **some** air flow enabled to protect the lens. | * The air assist is adjustable. Always make sure that it's enabled (on the top control panel) and that the valve (on the right hand side) is open. It's okay to reduce the air assist for delicate materials like paper, but there should always be **some** air flow enabled to protect the lens. | ||
* < | * < | ||
- | * The window is **tinted as all hell**. This should absorb the infra-red laser, and also absorbs literally all other light in the laser. | + | * The window is **tinted as all hell**. This should absorb the infra-red laser and most of the light from the laser. |
===== Checklists ===== | ===== Checklists ===== | ||
Line 105: | Line 135: | ||
* position the material on the bed and move the nozzle over the material | * position the material on the bed and move the nozzle over the material | ||
- | * release the locking ring on the nozzle | + | * release the locking ring on the nozzle |
* place the 12mm focus jig between the nozzle and the material, and lower the nozzle down to touch it | * place the 12mm focus jig between the nozzle and the material, and lower the nozzle down to touch it | ||
* if there isn't enough available movement of the nozzle, **remove the jig**, adjust the Z axis and try again | * if there isn't enough available movement of the nozzle, **remove the jig**, adjust the Z axis and try again | ||
- | * re-secure the nozzle and remove the jig | + | * re-secure the nozzle and remove the jig (turn {{img_20190528_203219_01.jpg? |
* check that the air assist is switched on and that the valve on the right-hand side is fully open | * check that the air assist is switched on and that the valve on the right-hand side is fully open | ||
* the air assist may be reduced for delicate materials such as paper and card, but some air should be kept on to protect the lens from smoke | * the air assist may be reduced for delicate materials such as paper and card, but some air should be kept on to protect the lens from smoke | ||
Line 128: | Line 158: | ||
* check that the rear access panel (laser power supply) is closed properly | * check that the rear access panel (laser power supply) is closed properly | ||
* check that the access controller is logged-in | * check that the access controller is logged-in | ||
+ | |||
+ | ==== Nozzle quickly " | ||
+ | In LaserCut 5.3, File> | ||
+ | Make sure "Quick speed" is set to a sensible value like 300, work-acc to 500 and space-acc to 500 | ||
==== Nozzle moves but doesn' | ==== Nozzle moves but doesn' | ||
Line 180: | Line 214: | ||
2018-07-19: | 2018-07-19: | ||
* The bed level was checked and it's within 1mm all over. The axes were checked and they' | * The bed level was checked and it's within 1mm all over. The axes were checked and they' | ||
+ | |||
+ | 2018-09-22: | ||
+ | * Tube #2 (from Smoke and Mirrors) installed. All mirrors realigned to a reasonable (but not perfect) standard. Power level set to 33%. | ||
===== Other Specifications (for maintenance) ===== | ===== Other Specifications (for maintenance) ===== | ||
Water tubing: silicone, 12mm OD, 8mm ID, 2mm wall\\ | Water tubing: silicone, 12mm OD, 8mm ID, 2mm wall\\ | ||
- | Chiller: CW-3000\\ | + | Chiller: CW-5200\\ |
Air assist compressor: Hailea ACO-328\\ | Air assist compressor: Hailea ACO-328\\ | ||
Air assist tubing: silicone, 12mm OD, 8mm ID, 2mm wall\\ | Air assist tubing: silicone, 12mm OD, 8mm ID, 2mm wall\\ | ||
Line 196: | Line 233: | ||
* {{ : | * {{ : | ||
* {{ : | * {{ : | ||
- | * {{ :cw-3000.pdf | CW-3000 Chiller Manual }} ({{ :cw-3000-2.pdf | alternative version | + | * {{ :cw-5000_5200_industrial_chiller_user_manual.pdf | CW-5200 Chiller Manual }} |
+ | * {{ :cw-5000_5200_industrial_chiller_maintenance_manual.pdf | CW-5200 Maintenance Manual | ||
* {{ : | * {{ : | ||
* {{ : | * {{ : |
lasercutter2.txt · Last modified: 2024-08-26 19:42 by danshearer