lasercutter
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
lasercutter [2018-02-15 12:36] – [Uncut/unengraved sections & inconsistent cuts] More guff gone al | lasercutter [2019-06-20 12:02] – old revision restored (2019-04-27 17:27) tim | ||
---|---|---|---|
Line 2: | Line 2: | ||
TRAINING REQUIRED BEFORE USE. | TRAINING REQUIRED BEFORE USE. | ||
+ | |||
+ | HOURS OF USE ARE LIMITED TO **8PM-8AM** UNTIL ADDITIONAL FUME EXTRACTION HAS BEEN INSTALLED. | ||
LS3060 from [[http:// | LS3060 from [[http:// | ||
Bed: 300x600mm\\ | Bed: 300x600mm\\ | ||
Laser: 40W glass CO2 | Laser: 40W glass CO2 | ||
+ | |||
+ | {{: | ||
+ | |||
+ | See also: [[lasercutter2|Laser Cutter #2]] | ||
===== Materials ===== | ===== Materials ===== | ||
Line 19: | Line 25: | ||
Engraving of some coated metals is possible, Martin has documented his experiences of [[engravingaluminium|engraving anodised aluminium]]. | Engraving of some coated metals is possible, Martin has documented his experiences of [[engravingaluminium|engraving anodised aluminium]]. | ||
+ | |||
+ | ===== Safety ===== | ||
+ | |||
+ | There is always a fire risk when using the laser. The laser should not be left unattended during a cut. | ||
+ | |||
+ | Failure to pay attention to the laser can result in this: | ||
+ | |||
+ | {{: | ||
===== Prices ===== | ===== Prices ===== | ||
Line 94: | Line 108: | ||
Download it again to the laser cutter. | Download it again to the laser cutter. | ||
- | ===== Acceptable temperature range of the water ===== | ||
- | |||
- | London Hackspace: 22 ± 3 °C (checked 24 June 2012) | ||
- | [[http:// | ||
- | The manual notes that you should change water if the temperature is higher than this degree. | ||
- | The temperature gets currently just measured on one point. The London Hackspace is currently monitoring the Laser cutter with coolbot but reports are reported. [[http:// | ||
===== Using Inkscape for lasering ===== | ===== Using Inkscape for lasering ===== | ||
Line 247: | Line 255: | ||
2017-12-16: | 2017-12-16: | ||
* Recalibrated power output: 36% = 9mA = 40W output. | * Recalibrated power output: 36% = 9mA = 40W output. | ||
+ | |||
+ | 2018-03-21: | ||
+ | * Laser cutter relocated to workbench. | ||
+ | * Water changed. | ||
+ | * Temperature sensors not currently available. | ||
+ | * Basic alignment check performed. | ||
+ | |||
+ | 2018-04-11: | ||
+ | * Nozzle replaced (smaller aperture fitted) | ||
+ | |||
+ | 2018-04-28: | ||
+ | * Mike actually tightened the nozzle up properly, fixing reported alignment/ | ||
+ | |||
+ | 2018-07-19: | ||
+ | * Mike re-calibrated the axes. Previously they were off by 1mm over 260mm in Y and 0.5mm over 180mm in X. | ||
+ | |||
+ | 2018-08-??: | ||
+ | |||
+ | * DIY chiller failed and was replaced with old ambient cooler from big laser. Seems to be keeping up with normal cutting/ | ||
+ | |||
+ | 2019-04-27: | ||
+ | * Laser hour-meter removed (718 hours on the clock). | ||
+ | * Tool access controller installed. | ||
===== Other Specifications (for maintenance) ===== | ===== Other Specifications (for maintenance) ===== | ||
Line 263: | Line 294: | ||
* [[http:// | * [[http:// | ||
* [[http:// | * [[http:// | ||
+ | * {{ : | ||
{{tag> | {{tag> |
lasercutter.txt · Last modified: 2023-12-24 13:37 by simon