lasercutter
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
lasercutter [2019-04-27 17:27] – tim | lasercutter [2023-07-05 18:57] – simon | ||
---|---|---|---|
Line 2: | Line 2: | ||
TRAINING REQUIRED BEFORE USE. | TRAINING REQUIRED BEFORE USE. | ||
- | |||
- | HOURS OF USE ARE LIMITED TO **8PM-8AM** UNTIL ADDITIONAL FUME EXTRACTION HAS BEEN INSTALLED. | ||
LS3060 from [[http:// | LS3060 from [[http:// | ||
Line 11: | Line 9: | ||
{{: | {{: | ||
- | See also: [[lasercutter2|Laser Cutter #2]] | + | See also: |
+ | * [[lasercutter2|Laser Cutter #2]] | ||
+ | * [[lasercutter_tips_and_tricks|Laser cutting tips and tricks]] | ||
===== Materials ===== | ===== Materials ===== | ||
Line 36: | Line 35: | ||
===== Prices ===== | ===== Prices ===== | ||
- | Usage is charged by cutting time: £5 per hour for members, £15 per hour for non-members. You don't need to pay for a full hour if you don't use it. | + | Usage is charged by cutting time: £0.09 per minute (£5.40 per hour) for members, £15 per hour for non-members. You don't need to pay for a full hour if you don't use it. |
- | Materials cost between £1.50 (3mm MDF) and £13 (6mm acrylic), per 300x660mm | + | Materials cost between £1.50 (3mm MDF) and £13 (6mm acrylic), per 300x600mm |
===== Power Levels ===== | ===== Power Levels ===== | ||
Line 50: | Line 49: | ||
Please add your own preferred settings here, but do not edit the existing entries. If you believe a setting is inappropriate, | Please add your own preferred settings here, but do not edit the existing entries. If you believe a setting is inappropriate, | ||
- | ^ Material ^ Engrave Speed ^ Engrave Power ^ Cut Speed ^ Cut Power ^ Notes ^ | + | ^ Material ^^ Cut Speed ^ Cut Power ^ Notes ^ |
- | | Acrylic | + | ^ Acrylic | 1mm | 12 | 98 | Recommended by Julian | |
- | | Acrylic 5mm | 200 | 21 | 3.5 | 98 | From HPC Manual | | + | | ::: | 2mm | 9.5 | 98 | Recommended by Julian | |
- | | Acrylic 10mm | 200 | 21 | 1 | 98 | From HPC Manual | | + | | ::: | 3mm | 8 | 98 | From HPC Manual | |
- | | Ply 1.5mm | 200 | 17 | 10 | 98 | From HPC Manual | | + | | ::: | 4mm | 4.5 | 98 | Recommended by Julian | |
- | | Ply 3mm | 200 | 17 | 7 | 98 | From HPC Manual | | + | | ::: | 5mm | 3.5 | 98 | From HPC Manual | |
- | | Ply 5mm | 200 | 17 | 7 | 98 | From HPC Manual | | + | | ::: | 5mm (black) | 3 | 98 | Recommended by Julian | |
- | | Ply 6mm | 200 | 17 | 1.5 | 98 | From HPC Manual | | + | | ::: | 8mm | 1.5 | 98 | Recommended by Julian | |
- | | MDF 3mm | 200 | 25 | 5 | 98 | From HPC Manual | | + | | ::: | 10mm | 1 | 98 | From HPC Manual | |
- | | MDF 4mm | 200 | 25 | 4 | 98 | From HPC Manual | | + | | ||||| |
- | | MDF 6mm | 200 | 25 | | | From HPC Manual | | + | ^ Ply | 1.5mm | 10 | 98 | From HPC Manual | |
- | | Corrugated Cardboard 3mm | 200 | 20 | 12 | 98 | From HPC Manual | | + | | ::: |
- | | Hardboard 3mm | | | 3 | 98 | From HPC Manual | | + | | ::: | 4mm | 7 | 98 | | |
- | | Paper | 200 | 15 | 20 | 20 | From HPC Manual | | + | | ::: | 5mm | 7 | 98 | From HPC Manual | |
- | | Card | 200 | 20 | 25 | 40 | From HPC Manual | | + | | ::: |
- | | Mount Board | 200 | 20 | 12 | 98 | From HPC Manual | + | | ||||| |
- | | Engraving Laminate | 20 | 21 | 15 | 80 | From HPC Manual | | + | ^ MDF |
- | | Engraving Laminate 1.5mm | 200 | 80 | 22 (x3 passes) | 80 | Recommended by Random | + | | ::: | 3mm | 5 | 98 | From HPC Manual | |
- | | Funky Foam | not suitable | + | | ::: | 4mm | 4 | 98 | From HPC Manual | |
+ | | ::: | ||
+ | | ||||| | ||
+ | ^ Laminate | 1.5mm | 22 (x3 passes) | 80 | Recommended by Random | | ||
+ | | ::: | 3mm | 15 | 80 | From HPC Manual | | ||
+ | | ||||| | ||
+ | | Corrugated Cardboard 3mm || 12 | 98 | From HPC Manual | | ||
+ | | Hardboard 3mm || 3 | 98 | From HPC Manual | | ||
+ | | Paper || 20 | 20 | From HPC Manual | | ||
+ | | Card || 25 | 40 | From HPC Manual | | ||
+ | | Mount Board || 12 | 98 | From HPC Manual | | ||
+ | | Funky Foam || 25 | 25 | From HPC Manual | | ||
+ | ^ Material ^ Engrave Speed ^ Engrave Power ^ Notes ^ | ||
+ | | Acrylic | 200 | 21 | From HPC Manual | | ||
+ | | Acrylic | 200 | 50 | Recommended by Julian | | ||
+ | | Ply | 200 | 17 | From HPC Manual | | ||
+ | | MDF | 200 | 25 | From HPC Manual | | ||
+ | | Corrugated Cardboard | 200 | 20 | From HPC Manual | | ||
+ | | Paper | 200 | 15 | From HPC Manual | | ||
+ | | Card | 200 | 20 | From HPC Manual | | ||
+ | | Mount Board | 200 | 20 | From HPC Manual | | ||
+ | | Engraving Laminate | 200 | 21 | From HPC Manual | | ||
+ | | Engraving Laminate | 200 | 80 | Recommended by Random | | ||
===== Z-axis adjustment/ | ===== Z-axis adjustment/ | ||
Line 145: | Line 165: | ||
The protective film is safe to cut, and protects the acrylic from smoke and accidental scratching. For engraving, the top layer of film should be removed as it can affect the quality of the engraving. | The protective film is safe to cut, and protects the acrylic from smoke and accidental scratching. For engraving, the top layer of film should be removed as it can affect the quality of the engraving. | ||
+ | |||
+ | ===== Other Specifications (for maintenance) ===== | ||
+ | |||
+ | Water tubing: silicone, 9.5mm OD, 6.3mm ID, 1.6mm wall\\ | ||
+ | Water pump: 2500L/hour (max), 2.5m head (max)\\ | ||
+ | Air compressor: Hailea ACO-328, 82L/min, pressure > | ||
+ | Air assist tubing: PVC, 6mm OD, 4mm ID, 1mm wall (approx)\\ | ||
+ | Mirrors: 20mm diameter\\ | ||
+ | Lens: 20mm diameter, ZnSe, 50.8mm focus | ||
+ | |||
+ | ===== Resources ===== | ||
+ | * [[http:// | ||
+ | * [[http:// | ||
+ | * {{: | ||
+ | * {{: | ||
+ | * [[http:// | ||
+ | * [[http:// | ||
+ | * {{ : | ||
+ | * [[https:// | ||
===== Log ===== | ===== Log ===== | ||
Line 279: | Line 318: | ||
* Tool access controller installed. | * Tool access controller installed. | ||
- | ===== Other Specifications (for maintenance) ===== | + | 2021-10-29: |
+ | * Realigned red laser to be correct | ||
- | Water tubing: silicone, 9.5mm OD, 6.3mm ID, 1.6mm wall\\ | + | 2022-05-25: |
- | Water pump: 2500L/hour (max), 2.5m head (max)\\ | + | * Clogged extraction filter cleaned |
- | Air compressor: Hailea ACO-328, 82L/min, pressure > | + | |
- | Air assist tubing: PVC, 6mm OD, 4mm ID, 1mm wall (approx)\\ | + | |
- | Mirrors: 20mm diameter\\ | + | |
- | Lens: 20mm diameter, ZnSe, 50.8mm focus | + | |
- | ===== Resources ===== | + | 2023-07-04: |
- | * [[http:// | + | * "The red laser tube is replaced and works! |
- | * [[http:// | + | * the speed/power table now needs to be sped up about x2 because it was made when the laser tube was aged a bit already |
- | * {{: | + | * 3mm plywood cuts reliably at 15 speed 100 power |
- | * [[http:// | + | * the water and inside of the previous laser tube was quite dirty, I would suggest changing the water every 6 months" |
- | * [[http://www.lbp.co.uk/pdfs/pdf_files/cleaning_co2_optics.pdf|Cleaning of CO2 laser optics]] | + | * <tim> So that's 320 hours for the old tube, which is disappointing. |
- | * {{ :lasercut_laser_palette.zip | Zeno's LaserCut5.3 Palette for Inkscape, makes all 40 layers colours match}} | + | * <tim> The old tube was calibrated to the rated 40w. Is it a good idea for the new one to be run at 55w? |
+ | * < | ||
+ | * < | ||
+ | * < | ||
+ | * < | ||
+ | * < | ||
+ | * < | ||
{{tag> | {{tag> |
lasercutter.txt · Last modified: 2023-12-24 13:37 by simon