purchases
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
purchases [2020-07-02 13:29] – tim | purchases [2020-11-02 22:08] – Clean up cazagen | ||
---|---|---|---|
Line 2: | Line 2: | ||
===== Pending Deliveries ===== | ===== Pending Deliveries ===== | ||
- | | + | |
+ | | ||
===== Small Stuff ===== | ===== Small Stuff ===== | ||
Line 9: | Line 10: | ||
TODO / Source: | TODO / Source: | ||
- | * Blue roll | + | |
- | * Hand soap | + | * Decent side cutters |
- | * Surface cleaner | + | |
CPC: | CPC: | ||
Line 28: | Line 29: | ||
Amazon: | Amazon: | ||
+ | |||
+ | * | ||
eBay/ | eBay/ | ||
+ | |||
* 0603 SMT resistors/ | * 0603 SMT resistors/ | ||
* I2C LCD adapter (re-stock for Tim) | * I2C LCD adapter (re-stock for Tim) | ||
+ | |||
RS: | RS: | ||
- | * Replacement Metcal soldering tip? | + | * |
Line 47: | Line 51: | ||
Costco: | Costco: | ||
+ | |||
+ | * Pepsi Max | ||
Other: | Other: | ||
- | * Blet for blet sander [[https:// | ||
* null modem / serial breakouts | * null modem / serial breakouts | ||
- | * layout paper (big masking tape) | ||
- | * flux | ||
- | * Raaco component drawers: 3x https:// | ||
- | * Hand sanitizer: | ||
- | * [[https:// | ||
- | * [[https:// | ||
- | |||
===== Small Tools ===== | ===== Small Tools ===== | ||
Line 99: | Line 97: | ||
* https:// | * https:// | ||
* https:// | * https:// | ||
- | |||
- | ===== Makita 18V Cordless System ===== | ||
- | |||
- | There is some support for the lab to start purchasing good quality cordless tools. Makita seems the most popular option, with a single system being desirable for sharing of batteries. < | ||
- | |||
- | Purchased already: | ||
- | |||
- | ^ Tool ^ | ||
- | | Dual charger | ||
- | | 4x 5.0Ah batteries | ||
- | | DJV181Z jigsaw | ||
- | | DTD154Z impact driver | | ||
- | | DGA517 angle grinder | ||
- | | DHS680 circular saw | | ||
- | | DCL180Z vacuum | ||
- | | DHP484 Drill | | ||
- | | DBO180Z orbital sander| | ||
- | |||
- | Wanted, in approximate priority order... | ||
- | |||
- | ^ Tool ^ Cost ^ Notes ^ | ||
- | |||
- | | DHP481 combi drill | [[https:// | ||
- | | DTM51 oscillating multi-tool | [[https:// | ||
- | | [[https:// | ||
- | |||
- | Other suggestions: | ||
- | |||
- | Drills: | ||
- | |||
- | * RMJ suffix = with battery | ||
- | * Z suffix = tool body only | ||
- | * DDF = drill drivers (no hammer mode) | ||
- | * DHP = combi drill (with hammer mode) | ||
- | * [[https:// | ||
- | * [[https:// | ||
- | * [[https:// | ||
- | * DHP484 is slightly heavier and stronger than DHP485, but not by much | ||
- | |||
- | Impact Bit Sets: | ||
- | |||
- | * < | ||
- | * [[https:// | ||
- | * [[https:// | ||
===== Air compressor ===== | ===== Air compressor ===== | ||
Line 157: | Line 111: | ||
[[https:// | [[https:// | ||
- | |||
- | ===== Workshop ===== | ||
- | |||
- | * < | ||
- | * Planer-thicknesser-jointer | ||
===== Electronics (G14) ===== | ===== Electronics (G14) ===== | ||
Line 193: | Line 142: | ||
* Total £265.62 | * Total £265.62 | ||
- | ===== Network ===== | ||
- | |||
- | Proposed purchase of SSDs for the new VM host: | ||
- | |||
- | 2x Samsung 860 EVO 1 TB SATA 2.5 Inch, from different batches: | ||
- | |||
- | * https:// | ||
- | * https:// | ||
- | |||
- | The write endurance of these drives will probably be sufficient for our needs, but we should monitor this and consider replacing one of them after 50% of the endurance has been consumed. | ||
purchases.txt · Last modified: 2024-05-18 19:26 by simon