startrite_bandsaw
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
startrite_bandsaw [2018-09-06 13:22] – [TODO] mike | startrite_bandsaw [2019-05-20 19:44] – Bandsawing practice. vzickus | ||
---|---|---|---|
Line 11: | Line 11: | ||
===== TODO ===== | ===== TODO ===== | ||
- | * < | ||
- | * < | ||
- | * < | ||
- | * < | ||
- | * < | ||
- | * < | ||
- | * < | ||
- | * < | ||
- | * < | ||
- | * Install VFD, DOL starter, access control, and wire up | ||
* Install dust collection | * Install dust collection | ||
- | * Write some training docs | + | ===== Training ===== |
- | * Fit new seal | + | |
- | ===== Costs ===== | + | Training for this tool can be given by either of the maintainers listed below. |
- | * Bandsaw £250 | + | See [[https:// |
- | * Delivery £148.66 | + | |
- | * V-belt £3.99 | + | |
- | * 5L gear oil £19.99 | + | |
- | * Gasket paper £4.10 | + | |
- | * DOL starter £29.99 | + | |
- | Total so far: £456.73 | + | Also see [[https://ehs.yale.edu/ |
+ | |||
+ | ===== Speeds ===== | ||
+ | |||
+ | ^ Material ^ Speed (feet/min) (thickness < 0.5") ^ Speed (feet/min) (thickness > 0.5") ^ | ||
+ | | Aluminium | 1000 | 700 | | ||
+ | | Brass - Cast | 320 | 180 | | ||
+ | | Brass - Soft | 1800 | 1000 | | ||
+ | | Cardboard | 3200 | 3200 | | ||
+ | | Copper | 1800 | 1000 | | ||
+ | | Iron - Cast | 180 | 100 | | ||
+ | | Leather | 3200 | 3200 | | ||
+ | | Plastics | 3200 | 3200 | | ||
+ | | Rubber | 3200 | 3200 | | ||
+ | | Silver | 1800 | 1800 | | ||
+ | | Steel | 180 | 180 | | ||
+ | | Wood | 3200 | 3200 | | ||
+ | |||
+ | ===== Saw blade width and minimum sawing radius ===== | ||
+ | This is only a guide. Always err on larger radius side. Use relief cuts, and drill relief holes where necessary. | ||
+ | | Saw blade width | 1/8" | 3/16" | 1/4" | 3/8" | 1/ | ||
+ | | Minimum sawing radius | 3/16" | 5/8" | 1" | 1 1/2" | 2 1/2" | 4"| 5 3/ | ||
+ | |||
+ | |||
+ | ===== Bandsawing practice ===== | ||
+ | |||
+ | Maximum saw blade life : Medium saw blade tooth pitch, speed and feed. | ||
+ | |||
+ | Minimum sawing time : Coarse tooth pitch, fast speed and heavy feed. | ||
+ | |||
+ | Fine accurate finish : Fine tooth pitch, fast speed and light feed. | ||
+ | ===== Trainers & Maintainers ===== | ||
+ | |||
+ | The following members are authorised to provide bandsaw training: | ||
+ | |||
+ | * Cameron Sharp (cazagen) | ||
+ | * Alfie Pates (alfie) | ||
+ | * Mike Walters (miek) | ||
+ | |||
+ | If something is up with the bandsaw please contact one of the following people: | ||
+ | * Cameron Sharp (cazagen) | ||
+ | * Mike Walters (miek) |
startrite_bandsaw.txt · Last modified: 2022-06-18 21:18 by mike