todo
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
todo [2016-09-27 09:41] – tim | todo [2019-08-06 10:06] – [Small Tasks] tim | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== | + | ====== To-Do (How can I help?) ====== |
- | ===== Mini Projects ===== | + | See also [[https:// |
- | ==== Fit shelving under G8 workbenches | + | ===== Small Tasks ===== |
- | We want to install shelving under the section of workbench to the right of the drill press. Just one shelf, | + | These should be immediately actionable, describable in a single bullet point and take up to 30 minutes for one person |
- | Status: Tim has fitted | + | * < |
+ | * < | ||
+ | * Install | ||
+ | * Tidy and clear-out the kitchen cupboard. Should only contain cleaning supplies. | ||
+ | * G1 hifi shelves: replace the short brackets with long brackets (we have a surplus and the shelf would be more secure). | ||
+ | * Laser Cutter #1: Connect the air-flow sensor into the safety loop (in series with the lid switch, water flow sensor, etc). | ||
+ | * < | ||
+ | * Wire-up power supplies for tool lockers and PAT test | ||
+ | ===== Bigger Tasks ===== | ||
- | ==== Drill organisation ==== | + | These should be immediately actionable, describable in a single bullet point and take 1-3 hours for 1-2 people to complete: |
- | All of our drills (bits) currently sit in a single box. We should have a storage system for making it easier | + | * Pull < |
+ | * < | ||
- | * Make or buy an organiser: | + | ===== Infrastructure Projects ===== |
- | * Multiple holes for each size of drill (because one drill of each size is not enough for a hackerspace) | + | |
- | * Sections for HSS, brad-point and masonry | + | |
- | * Audit the drills. Dispose of bad ones. Sharpen where possible. Identify what we need to purchase for replacements/ | + | |
- | * Identify a suitable drill sharpening system to keep the drills in good condition. | + | |
- | ==== Install ventilation in G8 Workshop ==== | + | More tasks may be found on the [[start# |
- | We have permission from Summerhall to install a fan in the external wall. There are two sections where previous vents have been bricked-up, and one of these should be opened and a fan installed. | + | ===== Mini Projects ===== |
- | * Plan how to remove the bricks safely | + | Projects might require planning or additional purchases before they can be tackled. Some projects will need their own pages and a link from here. |
- | * Source | + | |
- | * Do the work... | + | |
- | * Clean/ | + | |
- | ==== Relocate extraction vent in G11 Store Room ==== | + | ==== Repair Tektronix oscilloscope |
- | The extract vent is currently located in the left corner as you enter the room. It should be relocate to the tile above the rear of the server rack, to better capture the hot air. We have an extra length of flexible hose that should enable this. | + | Scope has a power supply fault, and probably needs a capacitor replacement. |
- | ===== New Room ===== | + | ==== Repair Rigol DS1102D oscilloscope |
- | G11: | + | One channel has failed, believed to be in the front-end. Device is out of warranty and Rigol cannot offer replacement parts that would be economically worth-while. |
- | * Fit PIR sensor < | + | This schematic might help: http:// |
- | + | ||
- | G8: | + | |
- | + | ||
- | * Arrange disposal/re-homing of the desks [Al] | + | |
- | * < | + | |
- | * Fit an external extractor fan (permission has been granted by Summerhall) | + | |
- | * Build a dust extraction system to capture dust from the power tools | + | |
- | * Purchase and install sensitive smoke alarm(s) to warn us before we cause a building evacuation | + | |
- | * Build a standalone workbench (either 150x75cm or 180x75cm) | + | |
- | * Fit shelf under right-section of new workbenches (40cm depth, wall-mounted) | + | |
===== Other Stuff ===== | ===== Other Stuff ===== | ||
* Design a test pattern for checking/ | * Design a test pattern for checking/ | ||
- | * Update OpenStreepMap | + | * Build a webapp |
- | * Sort the PC parts and peripherals | + | |
- | * < | + |
todo.txt · Last modified: 2022-07-04 19:30 by MirZa