tool_access_controllers
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
tool_access_controllers [2019-02-26 13:42] – [Bugs and Improvements] tim | tool_access_controllers [2022-12-29 17:04] – [Software] tim | ||
---|---|---|---|
Line 13: | Line 13: | ||
Current: | Current: | ||
- | * Clarke Bandsaw | ||
* Startrite Bandsaw | * Startrite Bandsaw | ||
* Bantam Lathe | * Bantam Lathe | ||
* EMCO Lathe | * EMCO Lathe | ||
+ | * Small Laser Cutter | ||
* Big Laser Cutter | * Big Laser Cutter | ||
* Mitre Saw | * Mitre Saw | ||
Line 22: | Line 22: | ||
* Sander | * Sander | ||
* Welder | * Welder | ||
+ | * CNC Router | ||
Planned: | Planned: | ||
- | * Small Laser Cutter | ||
- | * CNC Router | ||
* Bench grinder(s) | * Bench grinder(s) | ||
* Drill press(es) | * Drill press(es) | ||
Line 76: | Line 75: | ||
All of our current tool controllers use the same design, an [[https:// | All of our current tool controllers use the same design, an [[https:// | ||
- | The PCB, LCD and NFC modules are mounted on a laser-cut acrylic frame using nylon screws and spacers. Push buttons are panel-mounted to the front of the enclosure. | + | The PCB, LCD and NFC modules are mounted on a laser-cut acrylic frame using nylon screws and spacers. The front frame is cut from 3mm clear acrylic, and the supports from 2mm clear acrylic. Push buttons are panel-mounted to the front of the enclosure. |
+ | |||
+ | {{ : | ||
+ | {{ : | ||
**Simple plug-in mains tools:** | **Simple plug-in mains tools:** | ||
Line 90: | Line 92: | ||
More complex tools may have their own control systems (remote start/stop, VFD motor controllers, | More complex tools may have their own control systems (remote start/stop, VFD motor controllers, | ||
- | ===== Software ===== | + | ==== Safety Rules ==== |
- | https:// | + | * The tool controller must not be used as an emergency stop (though it may be wired in-series with a real emergency stop). |
+ | * The tool controller must not cause the device to start any motor or heavy machinery (there must be a separate start button with a no-volt reset). | ||
- | Two generations of firmware and backend-server are in use at the moment: | + | ===== Assembly Process ===== |
- | Legacy/ | + | - Assemble the PCB (see earlier section). |
- | * uses UDP networking with a simple retry mechanism | + | |
+ | - Solder five jumper wires to a PN532 module and use hot glue to support the joints. The wires will be connected to VCC, SDA, SCL, GND and the RSTPDN (reset) pin. At the other end the female connectors should be removed from their plastic housing and re-inserted into a 5-way housing. **WHAT LENGTH?** Adjust dip switches to I2C mode. | ||
+ | - Laser-cut a front-frame (3mm clear acrylic) and two support pieces (2mm clear acrylic). | ||
+ | - Place the frame inside the enclosure. Use it to mark the drill centres | ||
+ | - Double-check that the push buttons are on a straight line between the screw holes of the enclosure and that the holes will be symmetric. | ||
+ | - Drill the push button holes and use a hole reamer to get the exact size (the buttons will be inconveniently in-between common drill sizes). | ||
+ | - Drill holes for cable glands at the lower edge of the enclosure, or for non-glanded holes in the back of the enclosure (depending on the intended layout). | ||
+ | - Fit the acrylic supports in slots 1 (top of the enclosure) and 3. Use a piece of foam adhesive tape at each end to keep the supports in place and to apply upward pressure on the front-frame when it is installed later. | ||
+ | - Trim the header pins from an LCD module to provide enough clearance. | ||
+ | - Fit the LCD module to the front-frame using nylon screws (4x M3 10mm nylon screw, 8x nylon nut). The LCD should be mounted underneath the frame. The stack should be: screw head, front-frame, | ||
+ | - Fit the PCB to the front frame with nylon screws and hex spacers. The PCB should be mounted underneath the frame. The stack should be: screw head, front-frame, | ||
+ | - Fit the PN532 module to the front-frame. The module should be mounted **above** the frame. The stack should be: screw head, PN532 module, front-frame, | ||
+ | - Install the push buttons and place the assembled front-frame into the enclosure lid. | ||
+ | - Connect the PN532 and LCD modules. | ||
+ | - Install and test the firmware. | ||
+ | - Prepare mains wiring. For a plug-in configuration, | ||
+ | |||
+ | ===== Software ===== | ||
- | New: | + | [[https:// |
- | * uses TCP networking | + | [[https:// |
===== Bugs and Improvements ===== | ===== Bugs and Improvements ===== |
tool_access_controllers.txt · Last modified: 2023-09-10 09:11 by tim