toollockers
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
toollockers [2019-05-29 10:47] – [Parts] tim | toollockers [2019-06-27 09:44] – [Tasks] tim | ||
---|---|---|---|
Line 41: | Line 41: | ||
* Makita cordless tools (to avoid borrowing or theft) | * Makita cordless tools (to avoid borrowing or theft) | ||
+ | * Proxxon rotary tool kit (to avoid damage or loss of small parts) | ||
* Angle grinders (to ensure that users are trained) | * Angle grinders (to ensure that users are trained) | ||
* Good quality measurement tools (calipers, micrometers) | * Good quality measurement tools (calipers, micrometers) | ||
Line 48: | Line 49: | ||
* Cabinet installation | * Cabinet installation | ||
- | * Buy KALLAX cabinet (Tim will do this) | + | * <del>Buy KALLAX cabinet (Tim will do this)</ |
- | * Build KALLAX cabinet | + | * <del>Build KALLAX cabinet</ |
- | * Install a sheet of wood to close-off the back | + | * <del>Install a sheet of wood to close-off the back</ |
- | * Remove existing support leg from workbench | + | * <del>Remove existing support leg from workbench</ |
- | * Install cabinet under bench | + | * <del>Install cabinet under bench</ |
* Brace the workbench (transfer the load of the workbench onto the KALLAX) | * Brace the workbench (transfer the load of the workbench onto the KALLAX) | ||
* Doors | * Doors | ||
- | * Buy material from Hobarts (4x 800x450x6mm clear acrylic) | + | * <del>Buy material from Hobarts (4x 800x450x6mm clear acrylic)</ |
- | * Design the door for laser cutting: | + | * <del>Design the door for laser cutting:</ |
- | * 330x330mm | + | * <del>330x330mm</ |
- | * Rounded corners (say 5mm radius?) | + | * <del>Rounded corners (say 5mm radius?)</ |
- | * Holes for selected hinges | + | * <del>Holes for selected hinges</ |
- | * Holes for mounting lock and touch sensor plate | + | * <del>Holes for mounting lock and touch sensor plate</ |
- | * Test cut in MDF | + | * <del>Test cut in MDF</ |
+ | * Laser-cut 7 more doors | ||
* Fit to cabinet | * Fit to cabinet | ||
Line 72: | Line 74: | ||
* use alarm cable and leave a tail at the back of the cabinet for connection to the electronics | * use alarm cable and leave a tail at the back of the cabinet for connection to the electronics | ||
- | * Electronics | + | * Electronics |
* Based on tool access controller | * Based on tool access controller | ||
* Blue box with clear lid | * Blue box with clear lid | ||
Line 90: | Line 92: | ||
* Software | * Software | ||
- | * Will be based on the door/tool controller software | + | * Will be based on the door/tool controller software (with plenty of changes required) |
- | * (plenty of changes required) | + | * Status: |
- | * Tim is stuck with this task | + | * Mostly done. |
+ | * Minor change required to authentication class. | ||
+ | * WS2812 LED handling not implemented. | ||
+ | * Minor UI improvements required. | ||
===== Parts ===== | ===== Parts ===== | ||
Line 98: | Line 103: | ||
| [[https:// | | [[https:// | ||
| [[https:// | | [[https:// | ||
- | | [[https:// | + | | <del>[[https:// |
+ | | [[https:// | ||
| Touch plates | | | | Touch plates | | | ||
- | | Pop-rivets (for touch plates/ | + | | <del>Pop-rivets (for touch plates/ |
| Locks (DSCK7267) | in stock | | | Locks (DSCK7267) | in stock | | ||
| Touch sensors (TTP223) | in stock | | | Touch sensors (TTP223) | in stock | | ||
Line 108: | Line 114: | ||
| 12V 3A power supply | | | | 12V 3A power supply | | | ||
| 12V->5V DC-DC converter | | | | 12V->5V DC-DC converter | | | ||
- | | WS2812 LED strip | | | + | | WS2812 LED strip | needs to be ordered |
toollockers.txt · Last modified: 2020-11-01 13:39 by al