toollockers
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
| toollockers [2019-05-19 13:04] – tim | toollockers [2019-05-19 13:24] – [To Do] tim | ||
|---|---|---|---|
| Line 26: | Line 26: | ||
| Addressable RGB LED strip will be installed in each compartment to provide status feedback (tool checked in/out, compartments authorized after an NFC swipe). | Addressable RGB LED strip will be installed in each compartment to provide status feedback (tool checked in/out, compartments authorized after an NFC swipe). | ||
| + | |||
| + | ===== User Interface ===== | ||
| + | |||
| + | There will be one NFC reader for the group of 8 lockers. | ||
| + | |||
| + | * Present token to the reader | ||
| + | * Lockers that are authorized for the user will light up while others remain dark | ||
| + | * User touches the handle (touch plate) of the locker they wish to open | ||
| + | * Selected locker pops open. Other lockers deactivate (present token again to open another locker). | ||
| ===== Use Cases ===== | ===== Use Cases ===== | ||
| Line 38: | Line 47: | ||
| ===== To Do ===== | ===== To Do ===== | ||
| + | * Cabinet installation | ||
| + | * One existing support leg will need to be removed from the workbench | ||
| + | * Identify how to maintain the strength of the workbench (either a horizonal brace or transfer weight onto the cabinet) | ||
| * Doors | * Doors | ||
| * Identify appropriate size for the doors (compartments are 33x33cm so doors should be bigger) | * Identify appropriate size for the doors (compartments are 33x33cm so doors should be bigger) | ||
| Line 49: | Line 61: | ||
| * Create a spacer to mount the lock in the correct (repeatable) position | * Create a spacer to mount the lock in the correct (repeatable) position | ||
| * Decide how to screw the lock into the KALLAX | * Decide how to screw the lock into the KALLAX | ||
| - | * Install wiring | + | * Install wiring |
| + | * for lock release, lock sensor, touch sensor and LED strip | ||
| + | * use alarm cable and leave a tail at the back of the cabinet for connection to the electronics | ||
| * Electronics | * Electronics | ||
| * Relay board and I2C expanders are on order | * Relay board and I2C expanders are on order | ||
| Line 56: | Line 70: | ||
| * Will be based on the door/tool controller software | * Will be based on the door/tool controller software | ||
| * (plenty of changes required) | * (plenty of changes required) | ||
| + | |||
| + | ===== Parts ===== | ||
| + | |||
| + | | [[https:// | ||
| + | | Acrylic sheets | | | ||
| + | | Cabinet hinges | | | ||
| + | | Touch plates | | | ||
| + | | Pop-rivets (for touch plates/ | ||
| + | | Locks (DSCK7267) | in stock | | ||
| + | | Touch sensors (TTP223) | in stock | | ||
| + | | 8-way 12V relay module | ordered | | ||
| + | | I2C expanders (PCF8574) | ordered | | ||
| + | | Wemos D1 Mini ESP8266 | in stock | | ||
| + | | 12V 3A power supply | | | ||
| + | | 12V->5V DC-DC converter | | | ||
| + | | WS2812 LED strip | | | ||
toollockers.txt · Last modified: 2020-11-01 13:39 by al