Differences

This shows you the differences between two versions of the page.

--- voron_2_4_r2 [2023-02-19 15:33] – [Slicer Setup] MirZa
+++ voron_2_4_r2 [2023-06-08 11:43] – simon
@@ Line 1: / Line 1: @@
-====== Voron 2.4 r2 ======
+====== Voron 2.4 r2 (300mm³) ======
 Lended to the lab by Jacob Lewis
-**PLEASE NOTE THIS 3D PRINTER IS A WORK IN PROGRESS; IT IS EXPERIENCING ISSUES AND SHOULD NOT BE USED**
 ===== Costs =====
-^Material^Members/funders^Non-members^
+See [[3dprinters#costs]].
-|PLA|£0.30/m|£4/hour|
 ===== Materials =====
@@ Line 14: / Line 11: @@
 Same policy as the [[prusa_i3_mk_3|Original Prusa i3 MK3s]], if your materials are allowed on there, you may use them here.
-**ABS** - While this printer does have a carbon filter making it excellent for ABS, not all the panels have been mounted, stopping it from being sealed, so try to avoid printing ABS just yet.
+**ABS** - The printer is enclosed and has a carbon filter on the back so fumes shouldn't be an issue (MMV)
 **TPU/TPE** - Until a non-pei bed gets purchased, do not print this material as it will damage the PEI coating.
@@ Line 31: / Line 28: @@
 Before each print the printer will home, Quad gantry level and then home again.
-For now when homing you must watch the printer as it lowers to the endstop (Little metal button at back right, position 202,300) as occasionally the nozzle may miss this button causing the printer to be leveled incorrectly
+<del>For now when homing you must watch the printer as it lowers to the endstop (Little metal button at back right, position 202,300) as occasionally the nozzle may miss this button causing the printer to be leveled incorrectly</del>
+<del>As long as you run the extruder hot before the print starts, this is a non-issue, I will remedy this later.</del>
 **Quad gantry leveling** - The printer will sample 4 points across the bed allowing it to orient the flying gantry correctly. This may happen a few times until within tolerance.
@@ Line 44: / Line 42: @@
 ===== Slicer Setup =====
+There are 2 approved slicers:
-For now please use [[https://github.com/supermerill/SuperSlicer|SuperSlicer]], this is a fork of PrusaSlicer which has builtin presets for the Voron 2.4, setup is basically the same as the Prusa MK3. To setup a connection, go to **Printer Settings** and click the cog next to the preset at the top right. Use these settings:{{::fluidd-config.png?400|}}.
+  * PrusaSlicer (__Beta 2.6.0-alpha6 ONLY__)
+  * SuperSlicer (Note recent versions have been buggy)
+==== PrusaSlicer: ====
+The minimum supported version of PrusaSlicer is [[https://github.com/prusa3d/PrusaSlicer/releases/tag/version_2.6.0-alpha6| 2.6.0-alpha6]] as it is the only one which supports Klipper, which we use.
+The config file can be found [[https://github.com/Jaso55555/MyVoronConfig/blob/main/PrusaSlicer_config_bundle.ini|here]].
+First, under the printer selection dropdown menu, click "Add/remove printers" -> "Add/remove presets",
+then tick the box under "Other Vendors -> Voron", then on the new Voron section check "Voron FFF -> Voron v2 Afterburner Family -> Voron v2 300mm3 -> 0.4mm nozzle"
+Then import the config file using "File -> Import -> Config Bundle"
+Do check you're using the correct profiles as seen in this image:
+{{::voron_prusaslicer_settings_preview.png?direct&400|}}
+Do also check that the printer is connected properly. Go to the circled cog and hit test to see if it is working. If not, fill in the boxes using the settings for the superslicer setup below.
+==== Super Slicer: ====
+[[https://github.com/supermerill/SuperSlicer|SuperSlicer]]
+This is a fork of PrusaSlicer which has builtin presets for the Voron 2.4, setup is basically the same as the Prusa MK3. <del>To setup a connection, go to **Printer Settings** and click the cog next to the preset at the top right. Use these settings:{{::fluidd-config.png?400|}}.</del>
 First, under the printer selection dropdown menu, click "Add/remove printers" -> "Add/remove presets",
 then tick the box under "Voron -> Voron v2 Afterburner Family -> Voron v2 300mm3 -> 0.4mm nozzle"
-First, under the printer selection dropdown menu, click "Add/remove printers" -> "Add physical printer"
+<del>first, under the printer selection dropdown menu, click "Add/remove printers" -> "Add physical printer"
 Host Type: OctoPrint \\
-Hostname: voron24.hacklab
+Hostname: voron24.hacklab</del>
+You can import [[https://github.com/Jaso55555/MyVoronConfig/blob/main/SuperSlicer_config_bundle.ini]] under: File -> Import Config Bundle
 Once you have finished slicing, send the gcode to the web interface by clicking the send to printer button to the right of the **Export GCode**