voron_2_4_r2
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
voron_2_4_r2 [2023-06-08 11:43] – simon | voron_2_4_r2 [2023-11-04 15:52] – [Materials] dan | ||
---|---|---|---|
Line 9: | Line 9: | ||
===== Materials ===== | ===== Materials ===== | ||
- | Same policy as the [[prusa_i3_mk_3|Original Prusa i3 MK3s]], if your materials are allowed | + | Please speak to Jacob before using any filament not on this list. |
- | **ABS** - The printer is enclosed and has a carbon filter on the back so fumes shouldn' | + | ==== PLA ==== |
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
- | **TPU/TPE** - Until a non-pei | + | ==== PETG ==== |
+ | | ||
+ | | ||
+ | |||
+ | ==== ABS ==== | ||
+ | |||
+ | Please open the window and dangle the exhaust pipe outside for the duration of your print. | ||
+ | |||
+ | ==== TPU/ | ||
+ | |||
+ | Please use the alternate | ||
===== Rules ===== | ===== Rules ===== | ||
Line 27: | Line 45: | ||
Before each print the printer will home, Quad gantry level and then home again. | Before each print the printer will home, Quad gantry level and then home again. | ||
- | |||
- | < | ||
- | < | ||
**Quad gantry leveling** - The printer will sample 4 points across the bed allowing it to orient the flying gantry correctly. This may happen a few times until within tolerance. | **Quad gantry leveling** - The printer will sample 4 points across the bed allowing it to orient the flying gantry correctly. This may happen a few times until within tolerance. | ||
- | If layer shifts are occuring the XY belts may be loose. First check by moving the printhead | + | If layer shifts are occuring the XY belts may be loose. First check by moving the toolhead |
Line 44: | Line 59: | ||
There are 2 approved slicers: | There are 2 approved slicers: | ||
- | * PrusaSlicer (__Beta | + | * PrusaSlicer (Minimum supported version is 2.6.0) |
* SuperSlicer (Note recent versions have been buggy) | * SuperSlicer (Note recent versions have been buggy) | ||
==== PrusaSlicer: | ==== PrusaSlicer: | ||
- | The minimum supported | + | You can find the latest |
The config file can be found [[https:// | The config file can be found [[https:// | ||
- | First, under the printer selection dropdown menu, click " | + | To import |
- | then tick the box under "Other Vendors -> Voron", | + | |
- | + | ||
- | Then import the config file using "File -> Import -> Config Bundle" | + | |
- | Do check you're using the correct profiles as seen in this image: | + | ==== Super Slicer |
- | {{:: | + | |
- | Do also check that the printer is connected properly. Go to the circled cog and hit test to see if it is working. If not, fill in the boxes using the settings for the superslicer setup below. | + | |
- | ==== Super Slicer: ==== | + | |
[[https:// | [[https:// | ||
Line 90: | Line 99: | ||
If something has crashed, use Firmware Restart -> Restart Klipper inside the system sidebar. If this does not work try a power cycle. | If something has crashed, use Firmware Restart -> Restart Klipper inside the system sidebar. If this does not work try a power cycle. | ||
+ | |||
+ | |||
+ | |||
+ | ===== Common Printer Tasks ===== | ||
+ | |||
+ | |||
+ | ==== Changing Filament ==== | ||
+ | * Start by warming the nozzle via either the web interface or **Temperature > Ex0** on the built-in control panel | ||
+ | It should be set to the highest temperature of the previous material and the desired one | ||
+ | PLA: 200, PETG: 230, ABS: 240 | ||
+ | * Then either by using the web interface or **Filament > Unload Slow** retract the filament so it can be pulled out of the bowden tube at the back of the printer. | ||
+ | Please make sure to keep the filament tight on the spool, otherwise it can cause knots. Every spool has some form of holes in it which you can thread the filament through to keep it from unwinding. | ||
+ | * Next insert the new filament and extrude via the web interface or **Filament > Load Slow** | ||
+ | Keep doing this until the correct colour has been reached. Black filaments can stain the nozzle so this might need to be done a few times. | ||
+ | | ||
+ | | ||
+ | ==== Changing Nozzle ==== | ||
+ | The printer has been fitted with a Rapid-change revo extruder which allows quick and easy nozzle changes.\\ | ||
+ | We have 0.25mm (Yellow), 0.4mm (Red), 0.6mm (Blue) and 0.8mm (Green) nozzles. These are currently kept in a pink box above the voron. Extra silicon socks and hotside springs are also kept in the box if one breaks. | ||
+ | |||
+ | * Start by unloading the current filament and then cooling down the hotend (increasing the part cooling fan speed can help this go quicker). | ||
+ | * Then raise the printhead off the bed to allow access to the nozzle (using Move after Home). | ||
+ | * Unscrew the nozzle gently and screw in the new one. | ||
+ | |||
+ | * Next go into the web interface and go to **Sidebar > Config > printer.conf** | ||
+ | * At the top please comment/ | ||
+ | For example if you want the 0.25mm extruder, it should look like this: | ||
+ | # CHANGING NOZZLE/ | ||
+ | # Comment/ | ||
+ | [include revo-0.25.cfg] # Revo 0.25 | ||
+ | # [include revo-0.4.cfg] | ||
+ | # [include revo-0.6.cfg] | ||
+ | # [include revo-0.8.cfg] | ||
+ | |||
+ | * Hit **save & restart** at the top of the editor (this is not available on a phone, you need to **save** and then **restart**). **DO NOT TOUCH ANYTHING ELSE IN THE CONFIG FILE** | ||
+ | * Load filament and print as normal. Do make sure your slicer is updated to the correct nozzle size. | ||
+ | * Once you're done with the different nozzle, please swap it back to the 0.4mm one. | ||
+ |
voron_2_4_r2.txt · Last modified: 2024-07-17 15:24 by river