voron_2_4_r2
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
voron_2_4_r2 [2023-10-25 18:35] – [Changing Nozzle] simon | voron_2_4_r2 [2024-01-18 16:20] – jaso55555 | ||
---|---|---|---|
Line 9: | Line 9: | ||
===== Materials ===== | ===== Materials ===== | ||
- | Same policy as the [[prusa_i3_mk_3|Original Prusa i3 MK3s]], if your materials are allowed | + | Please speak to Jacob before using any filament not on this list. |
- | **ABS** - Please open the window and dangle the exhaust pipe outside for the duration of your print. | + | ==== PLA ==== |
+ | | ||
+ | | ||
+ | | ||
+ | | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
+ | * [[https:// | ||
- | **TPU/TPE** - Please use the alternate bed kept to the left of the printer, although this bed cannot be run above 60 degrees or the PET coating will be damaged. | + | |
+ | ==== PETG ==== | ||
+ | | ||
+ | | ||
+ | |||
+ | ==== ABS ==== | ||
+ | |||
+ | | ||
+ | | ||
+ | Please open the window and dangle the exhaust pipe outside for the duration of your print. | ||
+ | |||
+ | ==== TPU/TPE ==== | ||
+ | |||
+ | Please use the alternate bed kept to the left of the printer, although this bed cannot be run above 60 degrees or the PET coating will be damaged. | ||
+ | |||
+ | ==== Other Materials ==== | ||
+ | |||
+ | This printer has multiple nozzles, one of which is a [[https:// | ||
+ | Abrasive filaments include: | ||
+ | * Carbon fibre (CF) filaments | ||
+ | * Glow in the dark filaments | ||
+ | * Copperfill (Metalfill) filaments | ||
+ | * Wood filaments | ||
+ | * Conductive filaments | ||
+ | Please do some research before using these materials, and use the spare PEI bed and/or exhaust pipe if needed. | ||
===== Rules ===== | ===== Rules ===== | ||
Line 20: | Line 52: | ||
* Do not try to remove any SD cards, prints are uploaded via the web interface | * Do not try to remove any SD cards, prints are uploaded via the web interface | ||
* This printer is designed for hacking, however if you wish to modify it please message Jacob (Jaso55555# | * This printer is designed for hacking, however if you wish to modify it please message Jacob (Jaso55555# | ||
- | * Don't touch the config/ | + | * Don't touch the config/ |
* Don't use sharp tools on the PEI bed, it will scratch and damage it. If a print is stuck pull it off with pliers, bump it off with the corner of another print/ | * Don't use sharp tools on the PEI bed, it will scratch and damage it. If a print is stuck pull it off with pliers, bump it off with the corner of another print/ | ||
* Use the correct Gcode with this machine, generated with approved slicers. | * Use the correct Gcode with this machine, generated with approved slicers. | ||
Line 26: | Line 58: | ||
===== Calibration ===== | ===== Calibration ===== | ||
- | Before each print the printer will home, Quad gantry level and then home again. | + | Before each print the printer will home, Quad gantry level and then home again. |
**Quad gantry leveling** - The printer will sample 4 points across the bed allowing it to orient the flying gantry correctly. This may happen a few times until within tolerance. | **Quad gantry leveling** - The printer will sample 4 points across the bed allowing it to orient the flying gantry correctly. This may happen a few times until within tolerance. | ||
Line 99: | Line 131: | ||
==== Changing Nozzle ==== | ==== Changing Nozzle ==== | ||
The printer has been fitted with a Rapid-change revo extruder which allows quick and easy nozzle changes.\\ | The printer has been fitted with a Rapid-change revo extruder which allows quick and easy nozzle changes.\\ | ||
- | We have 0.25mm (Yellow), 0.4mm (Red), 0.6mm (Blue) and 0.8mm (Green) nozzles. These are currently kept in a pink box above the voron. Extra silicon socks and hotside springs are also kept in the box if one breaks. | + | We have 0.15mm (Pink), |
* Start by unloading the current filament and then cooling down the hotend (increasing the part cooling fan speed can help this go quicker). | * Start by unloading the current filament and then cooling down the hotend (increasing the part cooling fan speed can help this go quicker). | ||
- | * Then raise the printhead off the bed to allow access to the nozzle. | + | * Then raise the printhead off the bed to allow access to the nozzle |
* Unscrew the nozzle gently and screw in the new one. | * Unscrew the nozzle gently and screw in the new one. | ||
Line 110: | Line 142: | ||
# CHANGING NOZZLE/ | # CHANGING NOZZLE/ | ||
# Comment/ | # Comment/ | ||
- | [include revo-0.25.cfg] # Revo 0.25 | + | |
- | # [include revo-0.4.cfg] | + | |
- | # [include revo-0.6.cfg] | + | # [include revo-0.4.cfg] |
- | # [include revo-0.8.cfg] | + | # [include revo-0.6.cfg] |
+ | # [include revo-0.8.cfg] | ||
- | * Hit **save** at the top of the editor and then **restart** | + | * Hit **save |
* Load filament and print as normal. Do make sure your slicer is updated to the correct nozzle size. | * Load filament and print as normal. Do make sure your slicer is updated to the correct nozzle size. | ||
* Once you're done with the different nozzle, please swap it back to the 0.4mm one. | * Once you're done with the different nozzle, please swap it back to the 0.4mm one. | ||
voron_2_4_r2.txt · Last modified: 2024-07-17 15:24 by river