User Tools

Site Tools


g14_setup

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Next revisionBoth sides next revision
g14_setup [2019-07-28 16:57] – [Tasks] mikeg14_setup [2019-08-31 22:20] – [Tasks] tim
Line 5: Line 5:
 These tasks can be started now: These tasks can be started now:
  
-  * Order/source a combined euro-profile and handle for door.+  * <del>Install shelf for PCB etch tank</del> 
 +  * <del>Deep shelf for PSU and function generator</del> 
 +  * Shelves (see below) 
 +  * <del>Order/source a combined euro-profile and handle for door.</del>
   * Run 4 cat5 cables from G11 rack to G14 roof space   * Run 4 cat5 cables from G11 rack to G14 roof space
-  * Install UniFi access point +  * Sort/tidy/prepare electronics components for the move 
-  * <del>Order new legs for sink unit</del> +  * <del>Clean ESD mats and trim to match worktops</del> 
-  * Fit benches +  * <del>Install louvre panels on short wall below conduit [1 done, 2 to go]</del> 
-    * <del>Straighten the wavy worktop</del> +  * <del>Steal the worktop that currently covers the 2nd sink in G1. Cut it to make a 150x55cm shelf.</del> 
-    * Attach wooden battens to the wall to support the back of the worktops +  Obtain some chairs (3-4computer operator chairs or "guest" chairs)
-    * <del>Chamfer the worktop edges</del> +
-    * Sand & oil the worktops +
-      * <del>Coat 1</del> +
-      <del>Coat 2</del> drying till 2019-07-29 +
-      * Coat 3 +
-    * Attach legs and fit the worktopsattaching them to the battens with L brackets - slotted so they can move up and down a bit(?)+
  
 +===== Shelves =====
  
-===== Access control =====+The vertical brackets are installed but we will need to order more horizontals, and to source the shelf boards. Given the amount of worktop that we will be removing from G1 later on, it might be worth installing only a limited amount of shelving for now instead of buying new material.
  
-<del>The door will be fitted with the same type of lock as used for G2 and G8. The lock is currently on order and all other components are in stock.</del>+On the narrow end of the room, above the component drawers:
  
-Done!+  * 3 of 226cm x 30-31cm (slightly less than 226 to allow for the conduit).
  
-===== Floor =====+To the left of the window:
  
-The floor has damage that will need to be filled. Then it can be painted or covered with vinyl (this is a more practical task than for G1 as the space is small and already empty).+  * <del> 150cm x 54cm (for the function generator and HP power supply) </del> 
 +  * 150cm x 25-30cm (for oscilloscope, soldering tools, etc)
  
-ESD flooring has been proposed but is likely to be expensive. We have a roll of ESD flooring but it is soft (anti-fatigue, designed for standing workstations) and will be easily torn by chairs.+On the long wall:
  
-The sink cabinet can support its own (emptyweight if the legs are raised.+  * Many of ~290cm x 30cm (general storage) 
 +  * ~290cm x 25-30cm (for oscilloscope, soldering tools, etc)
  
-===== Networking =====+To the right of the sink, attached to wall and sink unit:
  
-Cables will be run from the server rack in G11 (2-4 would be appropriate). A UniFi access point will be installed (this is in stock). +  Recessed shelf for PCB etch tank.
- +
-===== Benches and storage ===== +
- +
-Proposed: 60-80cm benches against the long walls of the room. No bench on the short ends (because corners are too restrictive). Worktops will be installed at ~75cm height for seated use. +
- +
-Use the short end (away from the door) for component drawers and pick bins. Shelving over the benches (some mix of general storage and ready-to-use equipment). +
- +
-==== Cheap IKEA ==== +
- +
-[[https://www.ikea.com/gb/en/p/linnmon-table-top-white-20251139/|Linnmon 150x75cm]] £25 x4 +
- +
-Cheap, but not very durable. +
- +
-==== Solid Wood ==== +
- +
-[[https://www.ebay.co.uk/itm/Beech-Worktops-SALE-Farmhouse-Kitchen-Solid-Wood-Worktop-EU-Made/321370697566|Solid beech worktop 300x62x4cm]] £108 x2 +
- +
-==== Storage ==== +
- +
-On the short (far) wall: +
- +
-  pick bins below the conduit +
-  * component drawers above the conduit (up to 7 units can fit across the width of the wall). +
-  * normal shelves above the component drawers +
- +
-Above the conduit over the workbenches we will fit twinslot shelf rails: +
- +
-  * 15-30cm shelves above the conduit for oscilloscopes, soldering gear, etc. +
-  * louvre panels above for other tools and easy-access pick bins. +
-  * normal shelves above the panels. +
- +
-[[http://www.raacostorage.co.uk/raaco-1200-series-small-parts-storage-cabinet-1260-00-137386-c2x14054698|Raaco 1200]] - £42 each.\\ +
-[[http://www.raacostorage.co.uk/raaco-bin-wall-panel-c2x14057787|Raaco louvre panel]] - £12 each.\\ +
-Two Raaco panels with bins - £72-£83.+
  

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki