lasercutter_tips_and_tricks
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| lasercutter_tips_and_tricks [2019-10-15 01:24] – MirZa | lasercutter_tips_and_tricks [2023-12-20 23:47] (current) – Add Linux imagemagick info danshearer | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| Page for useful/cool things to do with the laser cutter for new and experienced users | Page for useful/cool things to do with the laser cutter for new and experienced users | ||
| + | |||
| + | ===== Resources / Project Ideas ===== | ||
| + | * [[https:// | ||
| + | * [[https:// | ||
| ===== Material tips ===== | ===== Material tips ===== | ||
| Line 16: | Line 20: | ||
| * The laser will however etch off paint and dye from metal. Anodised aluminium works great: [[engravingaluminium|]] | * The laser will however etch off paint and dye from metal. Anodised aluminium works great: [[engravingaluminium|]] | ||
| * To etch bare metal, it can be coated with a heat activated chemical (Molybdenum Disulphide). Sold as “Dry Moly Lube” : https:// | * To etch bare metal, it can be coated with a heat activated chemical (Molybdenum Disulphide). Sold as “Dry Moly Lube” : https:// | ||
| + | * Settings: 25 speed, 100 power, 0.5mm scan gap works fine (Costa) | ||
| * Thin metal can buckle from the heat - turning off Bi-dir and lowering power helps with this | * Thin metal can buckle from the heat - turning off Bi-dir and lowering power helps with this | ||
| * Costa has experience with this | * Costa has experience with this | ||
| Line 36: | Line 41: | ||
| * The edges of the thin [[https:// | * The edges of the thin [[https:// | ||
| * It might give a better result if cutting with multiple passes at lower power | * It might give a better result if cutting with multiple passes at lower power | ||
| + | |||
| + | **Glass** | ||
| + | *Glass can't be cut on the laser, but it can be " | ||
| + | *Engraving: https:// | ||
| + | *Engraving lines can be used to score glass for cutting https:// | ||
| **Food** | **Food** | ||
| Line 55: | Line 65: | ||
| * Human Skin (not a good idea) https:// | * Human Skin (not a good idea) https:// | ||
| + | **PLA** | ||
| + | * It can be cut but smells really bad so we don't recommend long cuts | ||
| + | * Material has a tendency to warp when heated up | ||
| + | * Longer and slower cuts can easily melt the material | ||
| + | * If cutting 3D printed material the laser may seal the infill inside (as if it was cauterizing) | ||
| ===== Techniques ===== | ===== Techniques ===== | ||
| Line 61: | Line 76: | ||
| * https:// | * https:// | ||
| * https:// | * https:// | ||
| + | |||
| + | **Box generators** | ||
| + | *[[https:// | ||
| + | *[[https:// | ||
| **Engraving Gray scale images** | **Engraving Gray scale images** | ||
| Line 68: | Line 87: | ||
| * Steps: | * Steps: | ||
| * Dither an image in Gimp or this online tool https:// | * Dither an image in Gimp or this online tool https:// | ||
| - | * use Gimp or ms paint to convert the image to a monochrome bitmap | + | * use Gimp or ms paint to convert the image to a monochrome bitmap, alternatively imagemagick using: **magick.exe in.png -monochrome -alpha off out.png** (Windows) or **convert in.png -monochrome -alpha off out.png** (Linux) |
| * open the image in LaserCut and scale it so one pixel corresponds to one line of the laser engrave (the height of the image in mm should equal the height of the image in pixels multiplied by the scan gap) | * open the image in LaserCut and scale it so one pixel corresponds to one line of the laser engrave (the height of the image in mm should equal the height of the image in pixels multiplied by the scan gap) | ||
| * You can preview the output by clicking on " | * You can preview the output by clicking on " | ||
| Line 79: | Line 98: | ||
| **Painting** | **Painting** | ||
| - | * Paint can be rubbed into etched areas in acrylic, then cleaned up with a wet cloth: https:// | + | * Paint can be rubbed into etched areas in acrylic |
| * Same can be done for wood: https:// | * Same can be done for wood: https:// | ||
| * Multiple colours can be done with repeated spray painting and engraving the reverse side of clear acrylic https:// | * Multiple colours can be done with repeated spray painting and engraving the reverse side of clear acrylic https:// | ||
| **Double sided engraving** | **Double sided engraving** | ||
| - | | + | * Cut and engrave your object and a mirror image of it next to it at the same time |
| - | | + | |
| * Switch the 2 copies around | * Switch the 2 copies around | ||
| * run the engrave again | * run the engrave again | ||
| + | |||
| + | **Rotary Axis** | ||
| + | *The Big laser has a rotary attachment for engraving and cutting cylindrical objects | ||
| + | *To use it: | ||
| + | *lower the bed of the laser down until you can see 2 switches and a socket on the right wall of the cutting area | ||
| + | *bring the laser head to roughly the centre of the bed | ||
| + | *plug in the rotary axis and flick both switches, this changes the laser from controlling the up/down motor to controlling the rotary axis motor | ||
| + | *cutting and engraving is done exactly the same as before, you may need to adjust the vertical scaling to get a nice result | ||
| + | *when you're done, don't forget to return the laser to the state you found it in | ||
| **Making rigid material flexible with living hinges** | **Making rigid material flexible with living hinges** | ||
| Line 99: | Line 126: | ||
| * This will require some trial and error | * This will require some trial and error | ||
| * Costa has experience with this | * Costa has experience with this | ||
| + | |||
| + | * Another method is to engrave from [[https:// | ||
| **Hatching** | **Hatching** | ||
| Line 105: | Line 134: | ||
| * TODO: insert image | * TODO: insert image | ||
| + | **Acrylic bending** | ||
| + | * Can be done with hair straightener or hot air gun | ||
| + | * Costa has made a nice jig for bending acrylic at precise angles, consisting of nichrome wire, 2 board boards and a hinge https:// | ||
| + | * This can also be done on the laser, using an out of focus beam or with the lens removed https:// | ||
| + | * Another cool example of this: https:// | ||
| ===== Design ===== | ===== Design ===== | ||
| **Removing duplicate lines** | **Removing duplicate lines** | ||
| Line 112: | Line 146: | ||
| **Kerf correction** | **Kerf correction** | ||
| + | |||
| + | Example of this in action (slope may be different for different materials and settings) in figure below: | ||
| {{https:// | {{https:// | ||
| + | * Pattern for testing out different tolerances for tight fitting finger joints: [[https:// | ||
| * Good explanation: | * Good explanation: | ||
| * The laser cutter has something called “kerf”, if you send a 1cm square to the laser, the part will come out slightly smaller (~9.8mm) | * The laser cutter has something called “kerf”, if you send a 1cm square to the laser, the part will come out slightly smaller (~9.8mm) | ||
| - | * This difference is about 0.1mm, so paths need to be offset by 0.1mm to compensate for this. | + | * This difference is about 0.1mm, so paths need to be offset by 0.1mm to compensate for this using the offset tool in Lasercut 5.3 |
| * Fusion 360 has a plugin which does kerf correction automatically: | * Fusion 360 has a plugin which does kerf correction automatically: | ||
| * This should also be possible with the “offset path” tool in any vector editing software like Inkscape or AI | * This should also be possible with the “offset path” tool in any vector editing software like Inkscape or AI | ||
| Line 127: | Line 164: | ||
| * [[https:// | * [[https:// | ||
| * [[https:// | * [[https:// | ||
| + | |||
| + | **General Laser cutter inaccuracies** | ||
| + | * https:// | ||
| ===== Material sourcing ===== | ===== Material sourcing ===== | ||
lasercutter_tips_and_tricks.1571102645.txt.gz · Last modified: 2019-10-15 01:24 by MirZa