User Tools

Site Tools


mqtt

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
mqtt [2020-02-10 21:03] – [Environment] cazagenmqtt [2024-02-14 08:03] (current) – [Lighting] simon
Line 18: Line 18:
 mosquitto_pub -h mqtt.hacklab -t 'dali/g1/preset/harmony' -n # send an empty message mosquitto_pub -h mqtt.hacklab -t 'dali/g1/preset/harmony' -n # send an empty message
 </code> </code>
 +
 +===== Devices =====
 +[[private:mqtt_devices|MQTT Smart devices login/Documentation]]
  
 ===== Sensors ===== ===== Sensors =====
Line 88: Line 91:
  
 ^ Topic ^ Payload ^ Notes ^ ^ Topic ^ Payload ^ Notes ^
-| environment/g1/extractor | 0=off, 1=on | Note that the radio link for this is patchy so may not work immediatelyDo not send multiple events to compensate as this should be done by the driver script instead. |+| environment/g1/extractor | 0=off, 1=on | [[https://github.com/edinburghhacklab/circuitpython_remote_relay|Controlled]] by {{:23-10-24_21-50-40_2656.jpg?linkonly|ESP32-S2 relay board}}. Debugging feedback availble on //debug/esp-487f307d5dad// |
 | environment/g1/heating | 0-30, off | Send a numeric value to set a target temperature for G1, off to turn the heating off | | environment/g1/heating | 0-30, off | Send a numeric value to set a target temperature for G1, off to turn the heating off |
 | environment/g8/extractor/relay/0 | 0=off, 1=on | Wall extractor in workshop | | environment/g8/extractor/relay/0 | 0=off, 1=on | Wall extractor in workshop |
-| environment/g14/heating/relay/0/set | 0=off, 1=on | Wall heater in G14+| environment/g14/heating | 0-30, off | Send a numeric value to set a target temperature for G14, off to turn the heating off | 
 +| espurna/g1-ceiling-air-purifier/relay/0/set | 0=off, 1=on | G1 Ceiling Air purifier (Smart Air Sqair) | 
 ===== Lighting ===== ===== Lighting =====
  
Line 102: Line 107:
 ^ Topic ^ Payload ^ Notes ^ ^ Topic ^ Payload ^ Notes ^
 | dali/g1/preset/<preset> | (none) | preset=off/dim/bright/corners/movie/comfort/presentation/harmony/random or preset=<number> | | dali/g1/preset/<preset> | (none) | preset=off/dim/bright/corners/movie/comfort/presentation/harmony/random or preset=<number> |
-| dali/g1/set/<light-id> | 0-254 | light-id=0-17, light-id=all, or light-id=social (just the end of the room with the kitchen) |+| dali/g1/set/<light-id> | [[g1_lighting#dali_light_level_presets|0-254]] | light-id=[[g1_lighting#dali_addresses|0-17]], light-id=all, or light-id=social (just the end of the room with the kitchen) |
 | dali/g1/script | json-formatted script | <code>[["set", 5,0], ["delay",2000], ["set_all",254]]</code> will set light number 5 to zero, wait for 2 seconds, then set everything to 254| | dali/g1/script | json-formatted script | <code>[["set", 5,0], ["delay",2000], ["set_all",254]]</code> will set light number 5 to zero, wait for 2 seconds, then set everything to 254|
  
 ^ Topic ^ Payload ^ Notes ^ ^ Topic ^ Payload ^ Notes ^
 | display/g1/blacklights/relay/0/set | 0=off 1=on | Switch the G1 blacklight on/off | | display/g1/blacklights/relay/0/set | 0=off 1=on | Switch the G1 blacklight on/off |
 +| display/g1/big_fricking_bulb | 0=off 1=on 2=toggle | Switch the giant 5W LED bulb on/off |
  
 ===== Displays ===== ===== Displays =====
Line 149: Line 155:
 The one that goes across the ceiling in the middle of the room. The one that goes across the ceiling in the middle of the room.
  
-These are running the WLED firmware, which is ridiculously comprehensive and can talk to basically everything.+These are running the WLED firmware, which is ridiculously comprehensive and can talk to basically everything. However, MQTT seems to have been disabled
  
-There is a web interface at http://ceilingleds.hacklab.+There is a web interface at http://wled-ceiling-string.hacklab.
  
-Full MQTT docs at https://github.com/Aircoookie/WLED/wiki/MQTT+<del>Full MQTT docs at https://github.com/Aircoookie/WLED/wiki/MQTT
  
 ^ Topic ^ Payload ^ Notes ^ ^ Topic ^ Payload ^ Notes ^
-| display/wled/g1/0 | 0-255, "ON", "OFF", or "T" |  "T" means toggle | +| display/g1/wled/$STRIP_NAME | 0-255, "ON", "OFF", or "T" |  "T" means toggle | 
-| display/wled/g1/0/col | #RRGGBB | |+| display/g1/wled/$STRIP_NAME/col | #RRGGBB | | 
 +|||STRIP_NAME can be replaced with "dangle" for the strip dangling in G1 or "all" for every strip running this firmware in G1|</del>
  
 ==== G1 Warning Turret ==== ==== G1 Warning Turret ====
Line 190: Line 197:
 | display/g1/projector/off | empty | Turns off projector |  | display/g1/projector/off | empty | Turns off projector | 
 | display/g1/projector/channel | text | Changes channel of radio to one of hdmi, vga, or svideo |  | display/g1/projector/channel | text | Changes channel of radio to one of hdmi, vga, or svideo | 
 +
 +==== Chart ====
 +
 +The blinky chart of the West of Scotland in G1.
 +
 +Note: Lighting mode may be overriden by hardware nya nya switch.
 +
 +^ Topic ^ Payload ^ Notes ^
 +| display/chart/mode | rainbow, normal | Engage nya nya rainbow mode, or normal light colours / patterns. |
 +
  
 ===== Access Control ===== ===== Access Control =====
 +
 +Code for this can be found on ehl-vm-things:/srv/docker/py3scripts/entrance-handler
 +
 +The door is opened by a small ESP8266 and a relay connected to the intercom phone under the IRC terminal in G1
  
 | access/entrance/request | | Button has been pressed at the entrance //read only// | | access/entrance/request | | Button has been pressed at the entrance //read only// |
Line 300: Line 321:
 There are 50 pixels on our tree, so 50 RGB values should be sent in each frame. There are 50 pixels on our tree, so 50 RGB values should be sent in each frame.
  
 +===== G1 Amp =====
 +
 +^ Topic ^ Payload ^ Notes ^
 +| sound/g1/amp/channel | channel_name | channel name, all caps e.g. HDMI1/AUDIO1. Some macros are stored such as pi/table | 
 +| sound/g1/amp/power | on/off | |
 +| sound/g1/amp/volume | up/down | currently this fades up/down the volume by 5dBm, this could be made to set the volume to a specific number, but that could go wrong... |
 ===== Misc ===== ===== Misc =====
  
mqtt.1581368611.txt.gz · Last modified: 2020-02-10 21:03 by cazagen

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki