Differences

This shows you the differences between two versions of the page.

--- mqtt [2022-05-27 21:29] – river
+++ mqtt [2024-02-14 08:03] (current) – [Lighting] simon
@@ Line 20: / Line 20: @@
 ===== Devices =====
-[[mqtt_devices|MQTT Smart devices login/Documentation]]
+[[private:mqtt_devices|MQTT Smart devices login/Documentation]]
 ===== Sensors =====
@@ Line 91: / Line 91: @@
 ^ Topic ^ Payload ^ Notes ^
-| environment/g1/extractor | 0=off, 1=on | Note that the radio link for this is patchy so may not work immediately. Do not send multiple events to compensate as this should be done by the driver script instead. |
+| environment/g1/extractor | 0=off, 1=on | [[https://github.com/edinburghhacklab/circuitpython_remote_relay|Controlled]] by {{:23-10-24_21-50-40_2656.jpg?linkonly|ESP32-S2 relay board}}. Debugging feedback availble on //debug/esp-487f307d5dad// |
 | environment/g1/heating | 0-30, off | Send a numeric value to set a target temperature for G1, off to turn the heating off |
 | environment/g8/extractor/relay/0 | 0=off, 1=on | Wall extractor in workshop |
@@ Line 107: / Line 107: @@
 ^ Topic ^ Payload ^ Notes ^
 | dali/g1/preset/<preset> | (none) | preset=off/dim/bright/corners/movie/comfort/presentation/harmony/random or preset=<number> |
-| dali/g1/set/<light-id> | 0-254 | light-id=0-17, light-id=all, or light-id=social (just the end of the room with the kitchen) |
+| dali/g1/set/<light-id> | [[g1_lighting#dali_light_level_presets|0-254]] | light-id=[[g1_lighting#dali_addresses|0-17]], light-id=all, or light-id=social (just the end of the room with the kitchen) |
 | dali/g1/script | json-formatted script | <code>[["set", 5,0], ["delay",2000], ["set_all",254]]</code> will set light number 5 to zero, wait for 2 seconds, then set everything to 254|
@@ Line 197: / Line 197: @@
 | display/g1/projector/off | empty | Turns off projector |
 | display/g1/projector/channel | text | Changes channel of radio to one of hdmi, vga, or svideo |
+==== Chart ====
+The blinky chart of the West of Scotland in G1.
+Note: Lighting mode may be overriden by hardware nya nya switch.
+^ Topic ^ Payload ^ Notes ^
+| display/chart/mode | rainbow, normal | Engage nya nya rainbow mode, or normal light colours / patterns. |
 ===== Access Control =====
+Code for this can be found on ehl-vm-things:/srv/docker/py3scripts/entrance-handler
+The door is opened by a small ESP8266 and a relay connected to the intercom phone under the IRC terminal in G1
 | access/entrance/request | | Button has been pressed at the entrance //read only// |
@@ Line 307: / Line 321: @@
 There are 50 pixels on our tree, so 50 RGB values should be sent in each frame.
+===== G1 Amp =====
+^ Topic ^ Payload ^ Notes ^
+| sound/g1/amp/channel | channel_name | channel name, all caps e.g. HDMI1/AUDIO1. Some macros are stored such as pi/table |
+| sound/g1/amp/power | on/off | |
+| sound/g1/amp/volume | up/down | currently this fades up/down the volume by 5dBm, this could be made to set the volume to a specific number, but that could go wrong... |
 ===== Misc =====