lasercutter2
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
lasercutter2 [2019-05-14 11:31] – [Recommended Settings] mirza | lasercutter2 [2019-07-21 21:59] – [Nozzle moves but doesn't cut] mirza | ||
---|---|---|---|
Line 3: | Line 3: | ||
TRAINING REQUIRED BEFORE USE.\\ | TRAINING REQUIRED BEFORE USE.\\ | ||
(Note: Access control is ad-hoc, Ask someone to add you after you have received a walkthrough.) | (Note: Access control is ad-hoc, Ask someone to add you after you have received a walkthrough.) | ||
- | |||
- | HOURS OF USE ARE LIMITED TO **8PM-8AM** UNTIL ADDITIONAL FUME EXTRACTION HAS BEEN INSTALLED. | ||
Model JD90125\\ | Model JD90125\\ | ||
Line 30: | Line 28: | ||
| Acrylic 1mm | 30 | 40 | Miron | | | Acrylic 1mm | 30 | 40 | Miron | | ||
| Acrylic 2mm | 28 | 100 | Miron | | | Acrylic 2mm | 28 | 100 | Miron | | ||
- | | Acrylic 3mm | 18 | 100 | Miron | | + | | Acrylic 3mm | <del>18</ |
| Acrylic 4mm | 15 | 100 | Miron | | | Acrylic 4mm | 15 | 100 | Miron | | ||
| Acrylic 5mm | 12 | 100 | Miron | | | Acrylic 5mm | 12 | 100 | Miron | | ||
- | | Acrylic 8mm | | | | | + | | Acrylic 8mm | 4 | 100 | David | |
| Acrylic 10mm | 3 | 100 | Miron | | | Acrylic 10mm | 3 | 100 | Miron | | ||
- | | Ply 3mm | < | + | | Ply 3mm | < |
| Ply 4mm | 20 | 100 | Miron | | | Ply 4mm | 20 | 100 | Miron | | ||
| Ply 6mm | 9 | 100 | Miron | | | Ply 6mm | 9 | 100 | Miron | | ||
Line 93: | Line 91: | ||
* < | * < | ||
</ | </ | ||
- | * Install ducts to roof and upgrade blower, to avoid releasing fumes onto courtyard users. **ACTION: | + | * Install ducts to roof and upgrade blower, to avoid releasing fumes onto courtyard users. **ACTION: |
* < | * < | ||
* Replace broken acrylic cover on front-loading slot. | * Replace broken acrylic cover on front-loading slot. | ||
Line 140: | Line 138: | ||
* position the material on the bed and move the nozzle over the material | * position the material on the bed and move the nozzle over the material | ||
- | * release the locking ring on the nozzle | + | * release the locking ring on the nozzle |
* place the 12mm focus jig between the nozzle and the material, and lower the nozzle down to touch it | * place the 12mm focus jig between the nozzle and the material, and lower the nozzle down to touch it | ||
* if there isn't enough available movement of the nozzle, **remove the jig**, adjust the Z axis and try again | * if there isn't enough available movement of the nozzle, **remove the jig**, adjust the Z axis and try again | ||
- | * re-secure the nozzle and remove the jig | + | * re-secure the nozzle and remove the jig (turn {{img_20190528_203219_01.jpg? |
* check that the air assist is switched on and that the valve on the right-hand side is fully open | * check that the air assist is switched on and that the valve on the right-hand side is fully open | ||
* the air assist may be reduced for delicate materials such as paper and card, but some air should be kept on to protect the lens from smoke | * the air assist may be reduced for delicate materials such as paper and card, but some air should be kept on to protect the lens from smoke | ||
Line 163: | Line 161: | ||
* check that the rear access panel (laser power supply) is closed properly | * check that the rear access panel (laser power supply) is closed properly | ||
* check that the access controller is logged-in | * check that the access controller is logged-in | ||
+ | |||
+ | ==== Nozzle quickly " | ||
+ | In LaserCut 5.3, File> | ||
+ | Make sure "Quick speed" is set to a sensible value like 300, work-acc to 500 and space-acc to 500 | ||
==== Nozzle moves but doesn' | ==== Nozzle moves but doesn' |
lasercutter2.txt · Last modified: 2023-12-24 13:36 by simon