User Tools

Site Tools


lasercutter2

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
lasercutter2 [2019-07-13 00:12]
DavidW
lasercutter2 [2019-07-23 22:46] (current)
mirza [Recommended Settings]
Line 3: Line 3:
 TRAINING REQUIRED BEFORE USE.\\ TRAINING REQUIRED BEFORE USE.\\
 (Note: Access control is ad-hoc, Ask someone to add you after you have received a walkthrough.) ​ (Note: Access control is ad-hoc, Ask someone to add you after you have received a walkthrough.) ​
- 
-HOURS OF USE ARE LIMITED TO **8PM-8AM** UNTIL ADDITIONAL FUME EXTRACTION HAS BEEN INSTALLED. 
  
 Model JD90125\\ Model JD90125\\
Line 30: Line 28:
 | Acrylic 1mm | 30 | 40 | Miron | | Acrylic 1mm | 30 | 40 | Miron |
 | Acrylic 2mm | 28 | 100 | Miron | | Acrylic 2mm | 28 | 100 | Miron |
-| Acrylic 3mm | <​del>​18</​del> ​17 | 100 | Miron, ​David(18 wasn't fully cutting) ​|+| Acrylic 3mm | 17 | 100 | David |
 | Acrylic 4mm | 15 | 100 | Miron | | Acrylic 4mm | 15 | 100 | Miron |
 | Acrylic 5mm | 12 | 100 | Miron | | Acrylic 5mm | 12 | 100 | Miron |
 | Acrylic 8mm | 4 | 100 | David | | Acrylic 8mm | 4 | 100 | David |
 | Acrylic 10mm | 3 | 100 | Miron | | Acrylic 10mm | 3 | 100 | Miron |
-| Ply 3mm | <​del>​30</​del> ​20 | 100 | <​del>​Miron</​del> ​Simon |+| Ply 3mm | 20 | 100 | Simon |
 | Ply 4mm | 20 | 100 | Miron | | Ply 4mm | 20 | 100 | Miron |
 | Ply 6mm | 9 | 100 | Miron | | Ply 6mm | 9 | 100 | Miron |
Line 47: Line 45:
 | Engraving Laminate 3mm |  |  |  | | Engraving Laminate 3mm |  |  |  |
  
-^ Material ^ Engrave Speed ^ (Range of) Engrave Power ^ Notes ^ +^ Material ^ Engrave Speed ^ Engrave Power ^ Notes ^ 
-| Acrylic |    +| Acrylic | 350 50 Miron 
-| Ply |    +| Ply | 350 50 Miron 
-| MDF |    +| MDF | 350 50 Miron 
-| Laminate |    |+| Laminate | 350 50 Miron |
  
 Minimum power setting for the laser to turn on: 19 Minimum power setting for the laser to turn on: 19
Line 63: Line 61:
   * <​del>​Clean laser tube water channels</​del>​   * <​del>​Clean laser tube water channels</​del>​
   * <​del>​Test optical power output and calibrate to a sensible maximum (e.g. 66% of peak rating)</​del>​   * <​del>​Test optical power output and calibrate to a sensible maximum (e.g. 66% of peak rating)</​del>​
-  * Create chart of power/speed settings for common materials (as a basic rule, multiply speeds from the old chart by 3x) +  * <del>Create chart of power/speed settings for common materials (as a basic rule, multiply speeds from the old chart by 3x)</​del>​
-    * Ply ✔ +
-    * MDF ✘ +
-    * Acrylic ✘+
   * <​del>​Documentation for existing laser cutter users</​del>​   * <​del>​Documentation for existing laser cutter users</​del>​
   * Update docs:   * Update docs:
Line 80: Line 75:
   * <​del>​Fit extraction duct mountings on right-hand access door (order delayed, re-sent 10th April)   * <​del>​Fit extraction duct mountings on right-hand access door (order delayed, re-sent 10th April)
 </​del>​ </​del>​
-  * Create spare focus jigs (requires 12mm acrylic, or a new design)+  * <del>Create spare focus jigs (requires 12mm acrylic, or a new design)</​del>​
   * Build and install monitoring system (laser usage, temperature logging)   * Build and install monitoring system (laser usage, temperature logging)
   * <​del>​Fully check and adjust alignment</​del>​   * <​del>​Fully check and adjust alignment</​del>​
Line 93: Line 88:
   * <​del>​Upgrade cutter-to-blower duct to PU or semi-flexible aluminium 150mm. **ACTION: MIKE**   * <​del>​Upgrade cutter-to-blower duct to PU or semi-flexible aluminium 150mm. **ACTION: MIKE**
 </​del>​ </​del>​
-  * Install ducts to roof and upgrade blower, to avoid releasing fumes onto courtyard users. **ACTION: PETE**+  * <del>Install ducts to roof and upgrade blower, to avoid releasing fumes onto courtyard users.</​del> ​**ACTION: PETE**
   * <​del>​Install LED lighting. **ACTION: ALFIE**</​del>​   * <​del>​Install LED lighting. **ACTION: ALFIE**</​del>​
   * Replace broken acrylic cover on front-loading slot.   * Replace broken acrylic cover on front-loading slot.
Line 163: Line 158:
   * check that the rear access panel (laser power supply) is closed properly   * check that the rear access panel (laser power supply) is closed properly
   * check that the access controller is logged-in   * check that the access controller is logged-in
 +
 +==== Nozzle quickly "​jumps"​ and looses alignment while moving between cuts ====
 +In LaserCut 5.3, File>​Machine Options>​Worktable
 +Make sure "Quick speed" is set to a sensible value like 300, work-acc to 500 and space-acc to 500
  
 ==== Nozzle moves but doesn'​t cut ==== ==== Nozzle moves but doesn'​t cut ====
lasercutter2.1562976738.txt.gz · Last modified: 2019-07-13 00:12 by DavidW